aa-fords.com

Very nice complete restoration, was done 10 Years ago. Runs good, drives like a truck, motor in very good condition, small amount of paint cracking on top of front fenders, small amount of paint chips 2 or 3. Pine bed with clear coating and with birch frame runners. Seems to be all orginal. Needs ti...

I receintly removed my Dual High, It was installed behind my 4 speed, kind of a mess installation, I put in an extension tube in its place. You can install a Dual High behind a normal 3 speed transmission, it would be a bolt in job, the Dual High has a place to bolt on a power take off. I liked the ...

When I was a kid my brother would drain the oil out of our 1941 John Deere H fill with kerosine, start it let it run for a few minutes, then drain and fill with proper oil never seemed to hurt it???????? John

I have a nice 1929 Model AA 1 1/2 truck, was restored 10 yrs ago, Wood stake bed has some paint problems cracking on the fenders and etc. The engine doesnt run quiet right need some work, havnt had a chance to work on it other projects seem more important right now. Would sell $10,000. Be glad to em...

Did you sell Molly and what did she bring? Thanks John

Update, I ended up replacing the core, After driving for about 20 minutes in 105 temp the engine temp was around 180 degrees. I think I am ok with it. John

sourdough, Sounds pretty rough for you, I had a stroke 2 1/2 years ago, which left me Paralized on my right side, I have gotten most of it back but it still doesnt work like it use to, I put two bolts in the top of my roof on my AA Doodlebug yesterday it took me about two hrs and before I could have...

Hayslip, i got all my bushiungs and bolts from Snyder the all fit very well, I will send a picture of the one I rebuilt. The leaf spring that is broken you can go to a spring shop they will make you another one. http://www.greenstore.org/IMG_6373z.jpg As you can tell I took out 12 leafs to make it r...

Update, I lengthened the drive shaft by 3/4" it now is 1/4" below top edge of bell, I am putting the axle on the top of the spring hanger to cut down on the angle of the drive shaft. The bolt I am using is 7/16" 1 1/4 Long Grade 5, with a half inch flat washer and two 7/16 flat washer...

Bob never thought about that, I will check before putting it back together, it has to be more than I thought about, i bet you hit on it. Thanks again. John

As you can see the bolt that held the U-Joint to the end of the extened drive shaft came out causing the u-joint to come apart. http://www.greenstore.org/IMG_6397z.jpg I purchased a used u-joint in nice shape, should I leave the bolt out or put it back in, I put 1/2" flat washer then a 7/16&quo...

Brian, I just sent my AA radiator to a shop that I have used before and highly recommened, I was told that they will pull both ends to see if it can be rodded, if it wont hold up to rodding they will replace the core. I am anxious to see how it comes out. It was boiling really bad in 103 Degree temp...

Brian, I replied to your email july 8 in it I said: Brian, It has 10 splines each end, a bolt came out of the short drive and got in the u-joint best I can tell and tore it up all of it is bad both ends and the cross. What would need out of the used one? I also need the center bolt and washer for th...

I know you guys wanted to see my u-joint



in the center of the picture is the bolt, must nhave come out and did the damage. John

I finally got the picture of the broken u-joint please give me your opinon of what happened

you notice the bolt in the middle of the picture, Im think came out and got into the u-joint. John