Search found 13 matches
- December 20th, 2015, 9:37 am
- Forum: AA Ford Discussion
- Topic: Front end caster
- Replies: 3
- Views: 4958
Front end caster
Can anyone help me on the caster adj and procedure1928. The truck seems to wander on the road. Rebuilt steering gearing,other things seem to be tight. Help would be appreciated
- September 24th, 2015, 6:48 am
- Forum: AA Ford Discussion
- Topic: Worm gears
- Replies: 0
- Views: 7651
Worm gears
Need help locating parts to change my gear ratio in the rear end. I want to increase the road speed from 7.5 to 1 to a lower ratio.
- August 29th, 2015, 9:33 am
- Forum: AA Ford Discussion
- Topic: Gear ratio
- Replies: 7
- Views: 7292
Gear ratio
Is it possible to chance the gear ratio on my 1928 AA with a worn drive rear end. Please advise
- August 11th, 2015, 4:57 pm
- Forum: AA Ford Discussion
- Topic: Powerhouse gen. Output
- Replies: 1
- Views: 1837
Powerhouse gen. Output
Need help with my generator output. 1928 with a powerhouse generator which put out up to 20volts . Have added a ground Cable from ground battery ter. to the bell housing without any difference. Checked voltage a gen , terminal block, amp meter, battery, all read 20 at half Throttle . The cut out is ...
- February 8th, 2015, 2:58 pm
- Forum: AA Ford Discussion
- Topic: Backfiring at high rpm
- Replies: 3
- Views: 2670
Backfiring at high rpm
My 1928 AA Truck is backing firing at half throttle and higher. I have replaced the condensor,adj the points to .020, timing the distributor using the front end pin. Am using org plugs. Starts fine with spark
Advance at half. What wrong. Need ADVICE.
Advance at half. What wrong. Need ADVICE.
- October 1st, 2014, 1:47 pm
- Forum: AA Buy and Sell
- Topic: Wanted: AA Radiator Shell
- Replies: 30
- Views: 17474
Re: Wanted: AA Radiator Shell
I have a raditor and she'll. I don'know the condition of the raditor and the shell is rusted but recoverable. In ct and nice and close.
- September 23rd, 2014, 4:38 am
- Forum: AA Ford Discussion
- Topic: Cab blocks
- Replies: 1
- Views: 2288
Cab blocks
Need advice on placement of wooden blocks from cab to frame on 1928 AA. Don't no where they go send pics.
- September 14th, 2014, 6:30 am
- Forum: AA Ford Discussion
- Topic: Body blocks
- Replies: 0
- Views: 3135
Body blocks
Can anyone send me a pic of the body block pattern for a 1928 aa?
Wickstop
Wickstop
- September 3rd, 2014, 4:03 pm
- Forum: AA Ford Discussion
- Topic: Tire size and tread pattern
- Replies: 17
- Views: 12007
Re: Tire size and tread pattern
I have bought firestone 650-20 with a truck pattern like the ones on my other 2 650-20. Can be seen on ebay under antique trk tires. The Co. selling is universal vintage tire co question call 800-233-3827. I paid $201 each. & $37.50 shipping. They match the other two. Good luck
WICKSTOP
WICKSTOP
- August 9th, 2014, 4:40 am
- Forum: AA Ford Discussion
- Topic: Water pump washer
- Replies: 4
- Views: 4380
Water pump washer
Rebuilding my water pump and their are 3bronze washers 1/8"x2" and don't know where
they belong. The center holes fit the pump shaft tightly. Need advice.
they belong. The center holes fit the pump shaft tightly. Need advice.
- July 22nd, 2014, 7:49 pm
- Forum: AA Ford Discussion
- Topic: Floor mat
- Replies: 2
- Views: 2171
Floor mat
Can anyone tell me where to buy a aa floor mat with the hand brake on the near left door post.
Wickstop
Wickstop
- June 25th, 2014, 2:58 pm
- Forum: AA Ford Discussion
- Topic: 1928speedometer cable
- Replies: 3
- Views: 2622
1928speedometer cable
I need help locating a source to purchase the inter cable I have the outer flexible tube. The speedometer has a square hole. Also how does the inter cable connect at the drive tube. Some type of sketch or book would help.
- May 20th, 2014, 12:55 pm
- Forum: AA Ford Discussion
- Topic: 1928 model AA body ID
- Replies: 1
- Views: 1972
1928 model AA body ID
Looking for someone to identify the body on my 1928AA w/131 1/2"wheel base. It is not a 89A express. It measures 46x14x91, 3tailgate hinges,3 1/2" I beam(2) with 3cross members,4hooks per side. HOPING someone has knowledge of the mfg.