Search found 51 matches

by emf
December 22nd, 2017, 6:18 am
Forum: AA Buy and Sell
Topic: Early 28 Frame & Springs
Replies: 7
Views: 772

Re: Early 28 Frame & Springs

Here are some photos. Your link does not show the differences between AA-5020 cross member and the AA-5020-B but this one looks the same as your drawings. That is, in my uneducated eye...
by emf
December 22nd, 2017, 5:46 am
Forum: AA Buy and Sell
Topic: Early 28 Frame & Springs
Replies: 7
Views: 772

Re: Early 28 Frame & Springs

Pardon me for not knowing the differences between two different frames offered in 1928. I thought the left side brake handle indicated early 28. I'll get a photo today...
by emf
December 21st, 2017, 5:16 am
Forum: AA Buy and Sell
Topic: Early 28 Frame & Springs
Replies: 7
Views: 772

Re: Early 28 Frame & Springs

That's $250.
by emf
December 21st, 2017, 5:16 am
Forum: AA Buy and Sell
Topic: Early 28 Frame & Springs
Replies: 7
Views: 772

Re: Early 28 Frame & Springs

Reduced to $20.
by emf
November 27th, 2017, 3:26 pm
Forum: AA Ford Discussion
Topic: Re: 28 AA brake adjust advice
Replies: 10
Views: 339

Re: 28 AA brake adjust advice

Is it possible that the hole where the adjuster goes through is egg shaped? Need to bush the hole???

Frank
by emf
November 5th, 2017, 5:25 am
Forum: AA Ford Discussion
Topic: 28/29 bevel gear high speed value
Replies: 8
Views: 472

Re: 28/29 bevel gear high speed value

It says above that it's free! :D
by emf
October 24th, 2017, 11:55 am
Forum: AA Ford Discussion
Topic: Putting Wire Spokes on the '28/'29
Replies: 15
Views: 1218

Re: Putting Wire Spokes on the '28/'29

Here ya go...
by emf
September 26th, 2017, 5:20 am
Forum: AA Buy and Sell
Topic: High Speed Odometer Gear
Replies: 5
Views: 727

Re: High Speed Odometer Gear

Sent PM
by emf
August 22nd, 2017, 8:00 am
Forum: AA Ford Discussion
Topic: Mitchell OD In MY AA - Update
Replies: 5
Views: 710

Re: Mitchell OD In MY AA - Update

When they shipped the unit to me, the shift mechanism was a cable set-up with the shift plunger attached to the original gear shift lever by using clamps. With this, connected via cable, it would avoid the dual high pedals.

Frank
by emf
August 21st, 2017, 4:55 pm
Forum: AA Ford Discussion
Topic: Mitchell OD In MY AA - Update
Replies: 5
Views: 710

Re: Mitchell OD In MY AA - Update

I don't think my pump takes up any more space than the dual high does. I have one on the shelf and it extends down below the shaft centerline about the same as my pump. The shifter is attached via a special cast aluminum adapter supplied by Mitchell. The adapter bolts to the shift tower and is used ...
by emf
August 21st, 2017, 12:18 pm
Forum: AA Ford Discussion
Topic: Mitchell OD In MY AA - Update
Replies: 5
Views: 710

Mitchell OD In MY AA - Update

I posted this on the Ford Barn, but since I said I'd report back here, here it is... Sorry for the long post... I thought I should bring everyone up to speed on my Mitchell Overdrive installation in my early 28 AA Firetruck. This is a 36% overdrive unit with a 3 speed transmission and a high speed r...
by emf
August 11th, 2017, 11:54 am
Forum: AA Ford Discussion
Topic: what lubricates roller bearings in AA drive shaft, outer shaft hot to touch
Replies: 10
Views: 1025

Re: what lubricates roller bearings in AA drive shaft, outer shaft hot to touch

birdacre and I have been sending emails back and forth regarding the bearing lubrication. I took some photos of mine and sent them to him, but I thought the info might be of use here. It is my belief that the bearings are lubricated from the u-joints, but why wouldn't a press-in grease fitting work ...
by emf
August 10th, 2017, 8:39 am
Forum: AA Buy and Sell
Topic: For Sale 28-29 coupling shaft
Replies: 2
Views: 714

Re: For Sale 28-29 coupling shaft

I sent a message to you. The roller bearings must get their lubrication from both ends. I do not see seals in either end... I still have the parts...

Frank
by emf
August 6th, 2017, 9:20 am
Forum: AA Ford Discussion
Topic: your opinion of mitchell overdrive
Replies: 6
Views: 579

Re: your opinion of mitchell overdrive

Yes, mine is the same worm ratio as yours. From what I understand, they have not made many to fit this rear. Call Mitchell, they can give you the latest price.

Frank
by emf
August 6th, 2017, 5:04 am
Forum: AA Ford Discussion
Topic: your opinion of mitchell overdrive
Replies: 6
Views: 579

Re: your opinion of mitchell overdrive

I recently took delivery on a Mitchell 36% overdrive, but have not installed it yes. VERY easy to install. I assembled it to a spare rebuilt rear. Next is to change assemblies with the one in the truck. I'll do that in the next week or so, if time permits. Very well built and the parts just go toget...