Search found 327 matches

by tiredtruckrestorer
March 8th, 2021, 5:59 pm
Forum: AA Buy and Sell
Topic: looking for a speedometer drive gear Ford-AA
Replies: 3
Views: 499

Re: looking for a speedometer drive gear Ford-AA

Hello Sir, I should be able to help you with those speedometer gears. Would you rather NOS parts or would good used ones be OK.

Keith
by tiredtruckrestorer
October 21st, 2020, 8:14 pm
Forum: AA Ford Discussion
Topic: battery disconnect switch
Replies: 7
Views: 1867

Re: battery disconnect switch

I have a truck that the previous owner mounted a heavy duty cut-off switch in the top hole of the left rear motor mount bracket. Only have to open the hood to get at it.

Keith
by tiredtruckrestorer
October 4th, 2020, 6:27 pm
Forum: AA Ford Discussion
Topic: Oversize Model A looking rear axle
Replies: 4
Views: 1963

Re: Oversize Model A looking rear axle

Thanks Ed for the info on where to find the markings on this rear end assembly. Probably wouldn't have noticed it unless I had an idea where to look. Mine has a "B" stamped on the upper end of the rear torque tube flange and it is the "high speed ratio". You're also quite right on how heavy these re...
by tiredtruckrestorer
September 25th, 2020, 5:54 pm
Forum: AA Ford Discussion
Topic: Oversize Model A looking rear axle
Replies: 4
Views: 1963

Oversize Model A looking rear axle

Does anybody have a "AA" rear axle that looks like a over-grown Model "A" one in their truck? According to the "Judging Standards" this is known as "Design 3" and was used beginning in early 1929. The "Design 4" low speed bevel gear AA rear was put into production in January 1930 with the high speed...
by tiredtruckrestorer
September 4th, 2020, 6:06 pm
Forum: AA Ford Discussion
Topic: U-Joint Grease: Cornhead or Today's Standards
Replies: 6
Views: 1877

Re: U-Joint Grease: Cornhead or Today's Standards

I use what they refer as cornhead grease in my steering boxes. Works well in them. Doesn't leak out like regular gear oil. Ford did recommend its' use in steering boxes a little later than the Model A period. Tractor Supply sells it. Probably won't hurt in the driveline once in a while to loosen the...
by tiredtruckrestorer
July 5th, 2020, 10:13 am
Forum: AA Ford Discussion
Topic: GarWood Dump box
Replies: 10
Views: 2710

Re: GarWood Dump box

My 1934 Wood brand bodies (built by Gar Wood Industries) brochure does show a model C-4 that was available in 1, 1 1/2, and 2 cubic yards. They all used the same D6 underbody hoist and states that these "standard sizes fit all short wheelbase 1 1/2 ton trucks". If you want copies of the literature o...
by tiredtruckrestorer
July 1st, 2020, 6:01 pm
Forum: AA Ford Discussion
Topic: GarWood Dump box
Replies: 10
Views: 2710

Re: GarWood Dump box

Elfox, I have quite a lot of Wood and GarWood literature. My early stuff lists the company as "Wood Hydraulic Hoist & Body Company--Detroit, Michigan". A February 1934 catalog lists the company as Gar Wood Industries, Inc at 7924 Riopelle Street, Detroit, Michigan. Probably just a name change when t...
by tiredtruckrestorer
April 27th, 2020, 7:38 pm
Forum: AA Ford Discussion
Topic: Grinding going into 4th gear
Replies: 2
Views: 2240

Re: Grinding going into 4th gear

When your shifting into high gear, you're are actually connecting the front of the mainshaft to the rear of the input shaft. Often I found that the front of the mainshaft is worn where the bearing rides on it and messes up the alignment between it and the input shaft. Other factors can also mess up ...
by tiredtruckrestorer
March 26th, 2020, 7:35 pm
Forum: AA Ford Discussion
Topic: Front Hub Dust Seal
Replies: 11
Views: 4828

Re: Front Hub Dust Seal

I have a NOS aftermarket felt seal that fits the front of 28-29 AA Ford trucks (according to the box it came in). It's comprised of two thin steel washers and a felt seal that goes between them. I don't remember the company that made it. I'll have to dig it out to see.

Keith
by tiredtruckrestorer
March 22nd, 2020, 6:35 am
Forum: AA Ford Discussion
Topic: 1930/31 Loose Ring gear Rivets
Replies: 5
Views: 4130

Re: 1930/31 Loose Ring gear Rivets

What you have to watch for is that rivet sizes are different than standard bolt sizes usually because the rivet was meant to be squashed to fit the hole tight (sometimes heated to achieve this). If you're going to try bolts, maybe a metric size would fit tighter in a rivet hole than a standard Ameri...
by tiredtruckrestorer
March 20th, 2020, 5:10 pm
Forum: AA Ford Discussion
Topic: Brake drums
Replies: 4
Views: 3413

Re: Brake drums

The pressed steel brake drums were ground true on brake drum grinding machines. I purchased a old truck brake drum grinding machine several years ago and did some AA drums. Unfortunately after the correct size grinding stones were used up, I couldn't find any more that were the right size. Often the...
by tiredtruckrestorer
February 4th, 2020, 2:34 pm
Forum: AA Ford Discussion
Topic: Power Take Off
Replies: 7
Views: 3072

Re: Power Take Off

Although my fire truck has a Barton pump driven off the front of the crankshaft, some fire trucks that have a midship mounted pump used a power-take-off.

Keith
by tiredtruckrestorer
February 1st, 2020, 7:25 pm
Forum: AA Ford Discussion
Topic: Chassis serial numbers?
Replies: 8
Views: 3138

Re: Chassis serial numbers?

David, sometimes the 4-speed transmission can help confirm the approximate date of the vehicle, as long as it hasn't been changed along the way. The "WG" (Warner Gear) transmissions usually have casting dates on them. The box usually has one on the drivers side, and the top cover usually has one cas...
by tiredtruckrestorer
January 26th, 2020, 6:32 pm
Forum: AA Ford Discussion
Topic: FAQ for AA dummies?
Replies: 18
Views: 8601

Re: FAQ for AA dummies?

Although Ford didn't use any positive seal arrangement in the rear of the engine, it shouldn't leak much there unless their is a problem. A "little" oil did helped lube the radius rod ball under the flywheel housing. If it's dripping a lot of oil something is wrong, either the main bearings have too...
by tiredtruckrestorer
January 8th, 2020, 4:29 pm
Forum: AA Ford Discussion
Topic: King Pin Bushing Orientation Question
Replies: 3
Views: 1714

Re: King Pin Bushing Orientation Question

The open end of both bushings face the axle.

Keith