Search found 1350 matches

by Bob C
March 7th, 2021, 6:28 pm
Forum: AA Ford Discussion
Topic: 88-A Platform Bed Questions
Replies: 3
Views: 49

Re: 88-A Platform Bed Questions

Aren't the holes for the steak locks?
Screen Shot 2021-03-07 at 6.25.09 PM.png
Screen Shot 2021-03-07 at 6.25.09 PM.png (73.38 KiB) Viewed 18 times
by Bob C
February 20th, 2021, 6:05 pm
Forum: AA Ford Discussion
Topic: Bevel Gear Rear End V-Bearing Question
Replies: 3
Views: 188

Re: Bevel Gear Rear End V-Bearing Question

I have two new sets of Timken 3982 carrier bearings. The older looking set has 20 rollers and the newer looking set has 22.
by Bob C
January 12th, 2021, 12:55 pm
Forum: AA Ford Discussion
Topic: Front Radiator Splash Shield Felt Question
Replies: 4
Views: 743

Re: Front Radiator Splash Shield Felt Question

Here are a couple of picture of one I have.
by Bob C
January 10th, 2021, 7:50 am
Forum: AA Ford Discussion
Topic: Coupler shaft and gear search
Replies: 1
Views: 509

Re: Coupler shaft and gear search

There is a short wheel base one on Ebay right now.
https://www.ebay.com/itm/1929-1931-Mode ... 7x&vxp=mtr
by Bob C
January 4th, 2021, 4:24 pm
Forum: AA Ford Discussion
Topic: Canadian Timken differential
Replies: 18
Views: 6568

Re: Canadian Timken differential

I looked in the parts book and the cone is AAC-100132 which cross to Timken/SKF/ Bower 385.
The cup is AAC-100131 which cross to Timken/ Bower 383, SKF K383.
by Bob C
January 4th, 2021, 9:01 am
Forum: AA Buy and Sell
Topic: locked up rusty transmission
Replies: 7
Views: 799

Re: locked up rusty transmission

sr230mike wrote:
January 3rd, 2021, 5:32 pm
Thank you . where is the discussion forum , where are we now?
Mike
You are in the buy and sell forum.
by Bob C
January 3rd, 2021, 12:30 pm
Forum: AA Buy and Sell
Topic: locked up rusty transmission
Replies: 7
Views: 799

Re: locked up rusty transmission

If the gears are that rusty the bearing probably aren't much better. I would pull the
trans and disassemble it. You might get more response if you put this in the discussion forum.
by Bob C
December 24th, 2020, 9:01 am
Forum: AA Ford Discussion
Topic: Cotter pins
Replies: 9
Views: 1095

Re: Cotter pins

They are listed in the parts book.
by Bob C
December 3rd, 2020, 6:03 pm
Forum: AA Ford Discussion
Topic: Drive shaft housing gaskets
Replies: 15
Views: 2902

Re: Drive shaft housing gaskets

OK, now I'm confused. Which gasket are we talking about, 4515 or 4516?
Flathead_Rear_Axle_Assy_1932to37.jpg
Flathead_Rear_Axle_Assy_1932to37.jpg (176.4 KiB) Viewed 1325 times
by Bob C
December 3rd, 2020, 8:19 am
Forum: AA Ford Discussion
Topic: Drive shaft housing gaskets
Replies: 15
Views: 2902

Re: Drive shaft housing gaskets

The originals were cork but looks like most of the current ones are felt, I've
even seen some that are a large rubber O-ring.
by Bob C
November 30th, 2020, 8:40 am
Forum: AA Ford Discussion
Topic: Drive shaft housing gaskets
Replies: 15
Views: 2902

Re: Drive shaft housing gaskets

I think the part you are looking for is A-4216, it's a Model A part not a AA part.
https://www.snydersantiqueauto.com/Prod ... /axle/rear
by Bob C
November 16th, 2020, 12:23 pm
Forum: AA Ford Discussion
Topic: Upholstery
Replies: 3
Views: 1465

Re: Upholstery

by Bob C
October 27th, 2020, 6:48 pm
Forum: AA Ford Discussion
Topic: U joint
Replies: 19
Views: 3125

Re: U joint

Before you get to far into rebuilding the u-joint I would take some measurements. To me it looks like
the AA-7084 cross is about .100" narrower than the A-7084 cross. Also the AA-7084 bushing OD looks larger
than the A-7084 bushing.
by Bob C
October 25th, 2020, 4:59 pm
Forum: AA Ford Discussion
Topic: Vin
Replies: 1
Views: 928

Re: Vin

Looks like the engine was built in January 1930.