Search found 1351 matches

by Bob C
March 23rd, 2021, 6:43 pm
Forum: AA Ford Discussion
Topic: Shimming bevel rear end.
Replies: 2
Views: 273

Re: Shimming bevel rear end.

I haven't been able to find much information either. The Service bulletins tell how to set up the pinion
but nothing on the carrier. I've looked in old Motors Truck Repair Manuals and Ford Rear Axle Repair Manual
and nothing on setting up the carrier.
truck rear axle.jpg
truck rear axle.jpg (299.47 KiB) Viewed 248 times
by Bob C
March 7th, 2021, 6:28 pm
Forum: AA Ford Discussion
Topic: 88-A Platform Bed Questions
Replies: 3
Views: 493

Re: 88-A Platform Bed Questions

Aren't the holes for the steak locks?
Screen Shot 2021-03-07 at 6.25.09 PM.png
Screen Shot 2021-03-07 at 6.25.09 PM.png (73.38 KiB) Viewed 458 times
by Bob C
February 20th, 2021, 6:05 pm
Forum: AA Ford Discussion
Topic: Bevel Gear Rear End V-Bearing Question
Replies: 4
Views: 571

Re: Bevel Gear Rear End V-Bearing Question

I have two new sets of Timken 3982 carrier bearings. The older looking set has 20 rollers and the newer looking set has 22.
by Bob C
January 12th, 2021, 12:55 pm
Forum: AA Ford Discussion
Topic: Front Radiator Splash Shield Felt Question
Replies: 4
Views: 1145

Re: Front Radiator Splash Shield Felt Question

Here are a couple of picture of one I have.
by Bob C
January 10th, 2021, 7:50 am
Forum: AA Ford Discussion
Topic: Coupler shaft and gear search
Replies: 1
Views: 813

Re: Coupler shaft and gear search

There is a short wheel base one on Ebay right now.
https://www.ebay.com/itm/1929-1931-Mode ... 7x&vxp=mtr
by Bob C
January 4th, 2021, 4:24 pm
Forum: AA Ford Discussion
Topic: Canadian Timken differential
Replies: 18
Views: 7295

Re: Canadian Timken differential

I looked in the parts book and the cone is AAC-100132 which cross to Timken/SKF/ Bower 385.
The cup is AAC-100131 which cross to Timken/ Bower 383, SKF K383.
by Bob C
January 4th, 2021, 9:01 am
Forum: AA Buy and Sell
Topic: locked up rusty transmission
Replies: 7
Views: 1188

Re: locked up rusty transmission

sr230mike wrote:
January 3rd, 2021, 5:32 pm
Thank you . where is the discussion forum , where are we now?
Mike
You are in the buy and sell forum.
by Bob C
January 3rd, 2021, 12:30 pm
Forum: AA Buy and Sell
Topic: locked up rusty transmission
Replies: 7
Views: 1188

Re: locked up rusty transmission

If the gears are that rusty the bearing probably aren't much better. I would pull the
trans and disassemble it. You might get more response if you put this in the discussion forum.
by Bob C
December 24th, 2020, 9:01 am
Forum: AA Ford Discussion
Topic: Cotter pins
Replies: 9
Views: 1678

Re: Cotter pins

They are listed in the parts book.
by Bob C
December 3rd, 2020, 6:03 pm
Forum: AA Ford Discussion
Topic: Drive shaft housing gaskets
Replies: 15
Views: 3635

Re: Drive shaft housing gaskets

OK, now I'm confused. Which gasket are we talking about, 4515 or 4516?
Flathead_Rear_Axle_Assy_1932to37.jpg
Flathead_Rear_Axle_Assy_1932to37.jpg (176.4 KiB) Viewed 1807 times
by Bob C
December 3rd, 2020, 8:19 am
Forum: AA Ford Discussion
Topic: Drive shaft housing gaskets
Replies: 15
Views: 3635

Re: Drive shaft housing gaskets

The originals were cork but looks like most of the current ones are felt, I've
even seen some that are a large rubber O-ring.
by Bob C
November 30th, 2020, 8:40 am
Forum: AA Ford Discussion
Topic: Drive shaft housing gaskets
Replies: 15
Views: 3635

Re: Drive shaft housing gaskets

I think the part you are looking for is A-4216, it's a Model A part not a AA part.
https://www.snydersantiqueauto.com/Prod ... /axle/rear
by Bob C
November 16th, 2020, 12:23 pm
Forum: AA Ford Discussion
Topic: Upholstery
Replies: 3
Views: 1756

Re: Upholstery

by Bob C
October 27th, 2020, 6:48 pm
Forum: AA Ford Discussion
Topic: U joint
Replies: 19
Views: 3844

Re: U joint

Before you get to far into rebuilding the u-joint I would take some measurements. To me it looks like
the AA-7084 cross is about .100" narrower than the A-7084 cross. Also the AA-7084 bushing OD looks larger
than the A-7084 bushing.