Search found 1164 matches

by Bob C
July 20th, 2018, 3:01 pm
Forum: AA Ford Discussion
Topic: what can be done about rod knock
Replies: 4
Views: 94

Re: what can be done about rod knock

The rods should have shims unless the bearings are so worn that all the shims have been removed.

Bob
by Bob C
July 16th, 2018, 2:56 pm
Forum: AA Ford Discussion
Topic: Ring and pinion gear set question
Replies: 14
Views: 264

Re: Ring and pinion gear set question

I found the bus listed in a 1956 Warner Gear catalog. It shows a Timken 53520 rear axle but the 5.14 ring gear they show is 34258 and the one you show is 34456 the pinion they show is 34271 and you show 34479 no other ratios are listed for that axle. The catalog shows a 53169 axle that uses the same...
by Bob C
July 15th, 2018, 5:10 pm
Forum: AA Ford Discussion
Topic: Ring and pinion gear set question
Replies: 14
Views: 264

Re: Ring and pinion gear set question

Well I've never heard of anybody wanting to go slower but they made a 6.6:1 gear set.

Bob
by Bob C
July 15th, 2018, 2:22 pm
Forum: AA Ford Discussion
Topic: Ring and pinion gear set question
Replies: 14
Views: 264

Re: Ring and pinion gear set question

This picture is for 1948-52 but the 1940-47 is similar.
Timken-Axle.jpg
Timken-Axle.jpg (656.37 KiB) Viewed 166 times
by Bob C
July 15th, 2018, 10:24 am
Forum: AA Ford Discussion
Topic: Ring and pinion gear set question
Replies: 14
Views: 264

Re: Ring and pinion gear set question

1940-47 ford used a pinion with a taper. Is this picture similar to your bus?

Bob
bus2.jpg
bus2.jpg (73.34 KiB) Viewed 179 times
by Bob C
July 14th, 2018, 11:10 am
Forum: AA Ford Discussion
Topic: Ring and pinion gear set question
Replies: 14
Views: 264

Re: Ring and pinion gear set question

Does it have a Ford Chassis and is it open or closed drive line??
Picture would help.

Bob
by Bob C
July 9th, 2018, 1:31 pm
Forum: AA Ford Discussion
Topic: Rear fenders
Replies: 10
Views: 332

Re: Rear fenders

by Bob C
July 7th, 2018, 8:17 pm
Forum: AA Ford Discussion
Topic: Express bed boards
Replies: 11
Views: 329

Re: Express bed boards

Page 28 of this link shows the groove for the platform bed which may be the same as you have.
https://aafordscom.ipage.com/aafords-pdf/185a.pdf

Bob
by Bob C
July 2nd, 2018, 7:39 am
Forum: AA Buy and Sell
Topic: Early '30 frame wanted
Replies: 10
Views: 297

Re: Early '30 frame wanted

Chris Haynes wrote:
July 1st, 2018, 10:18 am
I am looking for an Early 1930 AA Frame. Southwestern US preferred.
Are you looking for a particular serial number range or what??
From what Neil has posted it looks like the frames were the same
from January 1930 through March 1931.

Bob
by Bob C
June 30th, 2018, 9:21 am
Forum: AA Ford Discussion
Topic: Driveshaft bearing
Replies: 15
Views: 940

Re: Driveshaft bearing

The driveshaft should be 1 1/4" 10 spline.

Bob
by Bob C
June 28th, 2018, 8:30 am
Forum: AA Ford Discussion
Topic: New to the Forums and full of Questions
Replies: 2
Views: 149

Re: New to the Forums and full of Questions

The Warford replaces the coupling shaft.
IMAG0656_zps5feb9893.jpg
IMAG0656_zps5feb9893.jpg (72.41 KiB) Viewed 113 times
by Bob C
June 28th, 2018, 8:21 am
Forum: AA Ford Discussion
Topic: 28 AA warford overdrive
Replies: 4
Views: 203

Re: 28 AA warford overdrive

Haven't done the math but a 6.6 rear axle becomes a 4.94 in forth overdrive.
The Warford shifter is used to select under, direct, over, and neutral gears.
by Bob C
June 27th, 2018, 5:54 pm
Forum: AA Ford Discussion
Topic: Generator out put voltage
Replies: 1
Views: 137

Re: Generator out put voltage

The battery is what regulates the output voltage in the old Ford three brush generators.

Bob