Search found 400 matches
- January 29th, 2014, 12:30 pm
- Forum: AA Ford Discussion
- Topic: What are these shims for?
- Replies: 7
- Views: 4699
Re: What are these shims for?
Shelby, I have to respectively disagree with you, I don't believe a fiber washer would maintain the load that the hub and axle support, they would most likely crush after torqueing the axle nut. I sent these back and discussed this with Snyders, they were clueless on this subject, this part # A-4244...
- January 26th, 2014, 12:10 pm
- Forum: AA Club House
- Topic: been a while
- Replies: 2
- Views: 4638
Re: been a while
Hello Harry, Yes It as been a while, nice to see you are both out and about, we have done a lot of road work with Maggie this year with our club, the Palomar As, with short tours of 50 to 100 miles --- back roads and surface streets, trailer is feeling lonely we only used it twice last year. This pr...
- January 25th, 2014, 11:43 am
- Forum: AA Buy and Sell
- Topic: 4 sale Spring perches, Shackles, King pin bolts
- Replies: 7
- Views: 5013
Re: 4 sale Spring perches, Shackles, King pin bolts
The 28-29 AA came with front shocks, most were not replaced but occasionally you will see some still attached, they will not work on the 30-31 with the wider spring, the shock ball sits higher due to increase in truck height, here is a pic from Neil Wilson showing the difference.
- January 25th, 2014, 11:30 am
- Forum: AA Ford Discussion
- Topic: FRAME REPAIR
- Replies: 27
- Views: 15298
Re: FRAME REPAIR
Mac,
That's looking good,----- just like the old saying, you made a diamond out of a goats ass.
That's looking good,----- just like the old saying, you made a diamond out of a goats ass.
- January 24th, 2014, 1:47 pm
- Forum: AA Buy and Sell
- Topic: 4 sale Spring perches, Shackles, King pin bolts
- Replies: 7
- Views: 5013
4 sale Spring perches, Shackles, King pin bolts
I am currently replacing my front axle due to a badly worn king pin hole on the right side and alignment problems on the left, with one that I have rebuilt with replacement spindles, new pins and bushings, correct spring perches, and steering arms. At sometime in her life she had taken a good whack ...
- January 18th, 2014, 3:04 pm
- Forum: AA Ford Discussion
- Topic: WASTE NOT THOSE RIMS !
- Replies: 14
- Views: 7569
Re: WASTE NOT THOSE RIMS !
i see your far begone rim and raise you a 6 spoke! http://i141.photobucket.com/albums/r59/Sea_Slugs/Model%20AA%20Ford/100_0342.jpg one of the "spokes" was completely gone for 2 inches haha that wirey lookign thing is the bead Stakebed, Not mine, but can you believe someone had these for s...
- January 18th, 2014, 12:25 pm
- Forum: AA Ford Discussion
- Topic: WASTE NOT THOSE RIMS !
- Replies: 14
- Views: 7569
Re: WASTE NOT THOSE RIMS !
Don't need no stinking chisels, ------- just put some air in it and stand back.
- January 12th, 2014, 12:58 pm
- Forum: AA Ford Discussion
- Topic: Backwards dual hi
- Replies: 5
- Views: 4274
Re: Backwards dual hi
I have heard that it as been done, but have not seen anything explaining how it was done, the Hi-Low unit cannot be installed switching end for end that I can see as the large end would not clear the brake cross shaft, looking at the internals it doesn't seem likely that they could be switched eithe...
- December 31st, 2013, 12:34 pm
- Forum: AA Ford Discussion
- Topic: 1930 Ford AA Brake Question
- Replies: 21
- Views: 18398
Re: 1930 Ford AA Brake Question
I did have my steel drums turned on the rear, getting the drum centered was a challenge, and they need to be cut with small amounts of feed other wise the cutter will did in, it took most of an hour to do one of them, we also did not cut where the emergency brake shoes run, this allows for a little ...
- December 30th, 2013, 12:06 pm
- Forum: AA Ford Discussion
- Topic: Need Help with Brake question
- Replies: 5
- Views: 3714
Re: Need Help with Brake question
Hello Terry,
I am sure you have a parts price book, look at the illustrations and post the part # and cross check between the A and your 29 AA which I believe you need it for.
Brian, San Diego.
I am sure you have a parts price book, look at the illustrations and post the part # and cross check between the A and your 29 AA which I believe you need it for.
Brian, San Diego.
- December 9th, 2013, 1:41 pm
- Forum: AA Ford Discussion
- Topic: 29 AA rear end
- Replies: 5
- Views: 4428
Re: 29 AA rear end
As Bladehorse states modern gear oil will work, but be sure it is for use with yellow metals, this will lengthen the life of the ring gear whatever is left of it, I believe 2 quarts will do it, maybe three for topping up latter.
- December 7th, 2013, 2:47 pm
- Forum: AA Ford Discussion
- Topic: Switched rear ends on early 28.
- Replies: 5
- Views: 3527
Re: Switched rear ends on early 28.
Hello Dave, I believe there was a discussion on the Fordbarn regarding this as an upgrade on the model A and still retain the left handbrake, I am sure the AA would be included, I believe they discussed whether it would pass in fine point judging considering it was a safety issue, if I remember it w...
- November 26th, 2013, 1:17 pm
- Forum: AA Ford Discussion
- Topic: Seat springs
- Replies: 12
- Views: 7169
Re: Seat springs
Hello Roger,
Here are couple of pics that may help you, posted by a member of this board ?, I don't have any dimensions, do a search if you are fitting upholstery, if I remember it was discussed a few years ago.
Here are couple of pics that may help you, posted by a member of this board ?, I don't have any dimensions, do a search if you are fitting upholstery, if I remember it was discussed a few years ago.
- November 23rd, 2013, 1:58 pm
- Forum: AA Buy and Sell
- Topic: High speed rear end gears
- Replies: 7
- Views: 4678
Re: High speed rear end gears
Hello Dave,1crosscut wrote:Removed post and link.
Thanks,
Dave
Are you still going to sell the worm gear set? --- I may be interested. Thanks Brian.
- November 23rd, 2013, 1:53 pm
- Forum: AA Buy and Sell
- Topic: 131 Frame pieces wanted
- Replies: 5
- Views: 4253
Re: 131 Frame pieces wanted
I may have the rear section of frame that your looking for if they just cut off after the rear crossmember. Message me your emai I'll send you a picture of what I have Thanks. Joe Hello Joe, Please send pics of the frame rail parts you have, I have just sent you an e-mail thru the forum, I think I ...