Search found 210 matches

by Hayslip
February 2nd, 2016, 7:59 am
Forum: AA Buy and Sell
Topic: looking for 3 hole hood latch and gas cap
Replies: 4
Views: 2089

Re: looking for 3 hole hood latch and gas cap

The 1928 hood handles were drop forged, that is just the hook part. These are not reproduced. As a running change the handle was changed to a stamping sometime in the 1928-1929 period. It's not clear from the above which is requested.
by Hayslip
December 9th, 2015, 2:02 pm
Forum: AA Ford Discussion
Topic: Indented Door for side mount
Replies: 8
Views: 2633

Re: Indented Door for side mount

See my The "non" dented fender post on the AA Club House dated Sept.09,2014 of a well maintained AA heavy duty express with a fender well, but a plain door. Excuse my heading; I meant door at the time.
by Hayslip
December 5th, 2015, 6:57 am
Forum: AA Ford Discussion
Topic: 31 delux wire wheels
Replies: 21
Views: 5279

Re: 31 delux wire wheels

In the photo of the rear end note the wire wheel hub does NOT butt up against the brake drum. A gap here. A BAD idea trying to fit the 1928 style wheel on a 1930 hub.. No support here. This truck originally had an aftermarket cab/body. Note the sheet metal to make the A pillar fit aftermarket cab.
by Hayslip
December 1st, 2015, 6:31 am
Forum: AA Ford Discussion
Topic: SPEEDO CABLE FRAME BRACKET
Replies: 3
Views: 1437

Re: SPEEDO CABLE FRAME BRACKET

Passenger side top of frame opposite transmission next to the body bracket is a hole. I think that is the correct hole.
by Hayslip
September 28th, 2015, 6:07 am
Forum: AA Ford Discussion
Topic: 29 bevel gear rear end
Replies: 12
Views: 3333

Re: 29 bevel gear rear end

Gone, but not forgotten: The Ford Indianapolis Service letters of April 27,1931 page 5 states: "AA-4029-B driving gear and drive shaft matched 5.11 to 1 have been reinstated for service to be installed in the 1928-29 Banjo type sear axle only".
by Hayslip
September 23rd, 2015, 12:56 pm
Forum: AA Ford Discussion
Topic: 29 bevel gear rear end
Replies: 12
Views: 3333

Re: 29 bevel gear rear end

The rear end that looks like the car of 1928-1948, that is in 3 pieces is a domestic Ford factory product. The torque tube is also unique for this rear end.
by Hayslip
September 1st, 2015, 11:47 am
Forum: AA Ford Discussion
Topic: Trany accesory?
Replies: 6
Views: 1971

Re: Trany accesory?

A look at the production line in early 1928 the body was dropped onto the frame with the brake handle in place and would have to be slipped through the small slot in the body sill. When they changed the braking system in front of the shift made dropping the cab easier. The "front of the shift" versi...
by Hayslip
July 21st, 2015, 6:12 am
Forum: AA Ford Discussion
Topic: Headlight bar lengths
Replies: 1
Views: 1202

Re: Headlight bar lengths

The 1928-June 1930 bar is flat between the two headlights. The 1930-31 style is arched from headlight to headlight. If you have a Jan-June 1930 truck use the early style. Some trucks of this period still had the 1929 style headlamps, but all used the early bar regardless of lamps.
by Hayslip
July 5th, 2015, 3:59 pm
Forum: AA Buy and Sell
Topic: early 1928AA
Replies: 0
Views: 4163

early 1928AA

See www.rufusranch.com. Truck is the early 4 cross member version, high rear window cab too.
by Hayslip
June 25th, 2015, 11:40 am
Forum: AA Ford Discussion
Topic: Muffler hanger
Replies: 6
Views: 2214

Re: Muffler hanger

Take a look at the frame about 3 1/2 inches after the 2nd running board bracket. You should find two holes one above the other about 2 inches apart. The bracket lines up with these holes. As I recall the nuts are on the outside of the frame. Slip the bracket over the pipe first then bolt up. Best, Ed
by Hayslip
June 20th, 2015, 6:03 am
Forum: AA Ford Discussion
Topic: 28/29 AA Brake rod anti rattler questions
Replies: 2
Views: 1433

Re: 28/29 AA Brake rod anti rattler questions

The flat springs are the same for car and AA truck. The idler has a coil return spring illustrated in the latest club news (Hint:join the club). Installation is shown in the Service Bulletins. There are several coil springs; one is available from vendors. Best, Ed
by Hayslip
June 15th, 2015, 7:04 am
Forum: AA Ford Discussion
Topic: AA radiator splash apron
Replies: 3
Views: 1722

Re: AA radiator splash apron

The car and truck sheet metal is the same; there are no unique AA aprons. The 28/29/early 30 AA had an apron attached to the vehicle by 4 oval head screws passing vertically through holes in the hood shelves into 4 threaded tabs on the outside of the apron. The 30/31 style is attached with with 4 lo...
by Hayslip
June 6th, 2015, 6:29 am
Forum: AA Buy and Sell
Topic: AA truck for sale at www.rufusranch.com
Replies: 2
Views: 1737

AA truck for sale at www.rufusranch.com

They have it listed as a 1928; appears to be a 1929 with a 82A cab and aftermarket flat bed.
by Hayslip
May 15th, 2015, 4:17 pm
Forum: AA Ford Discussion
Topic: interesting couplingshaft found on 31AA anyone know about?
Replies: 7
Views: 2130

Re: interesting couplingshaft found on 31AA anyone know abo

See the 1932 Service Bulletins for this shaft. It was a good idea;, saves a lot of work to replace a clutch.
by Hayslip
March 29th, 2015, 9:07 am
Forum: AA Buy and Sell
Topic: Indented 82B cab driver's door
Replies: 0
Views: 2303

Indented 82B cab driver's door

At the Maynard, MA flea today there was a door with the dent for $450. The owner(Joe) can be reached at Massachusetts number 508-584-2490. This vendor also has a passenger side door for sale.