Search found 469 matches

by KimVanOrder
January 15th, 2015, 7:51 pm
Forum: AA Ford Discussion
Topic: 1928 rear ratio
Replies: 16
Views: 2220

1928 rear ratio

Was the '28 AA available with both the low and high speed worm drive rear end? I have a low speed in the truck now and want to know if it is "proper" to put in the higher speed ratio.

Thanks in advance for your input.

KVO
by KimVanOrder
January 7th, 2015, 4:32 pm
Forum: AA Club House
Topic: Miles Driven In 2014
Replies: 1
Views: 2775

Re: Miles Driven In 2014

Good for you!!! Now strap on the chains and drive it in the snow drifts.... :mrgreen:
by KimVanOrder
December 28th, 2014, 3:17 pm
Forum: AA Ford Discussion
Topic: AA Dual Wheel Rear Fenders
Replies: 26
Views: 4374

Re: AA Dual Wheel Rear Fenders

It would be nice to have an AA'er close to Benson who could make visits and get free copies of drawings.[/quote]


Where is he at?
by KimVanOrder
December 20th, 2014, 3:42 pm
Forum: AA Ford Discussion
Topic: Dovetail bumper??
Replies: 7
Views: 1237

Re: Dovetail bumper??

On my '28 the inside trim has two screws that hold it down then it slides up out of the way and the rubber bumper slides out. ( At least that is how I took mine out). Not back together yet. Paint is still Drying. :|
by KimVanOrder
December 12th, 2014, 4:25 pm
Forum: AA Ford Discussion
Topic: Head light alignment
Replies: 5
Views: 1081

Re: Head light alignment

Dito:

I got new reflectors, Not that great. I think they are not the correct shape. Be sure to get good ones. Not the "Bright and shinny", ones. (nuf said)?
by KimVanOrder
December 4th, 2014, 3:22 pm
Forum: AA Buy and Sell
Topic: '29 AA running boards
Replies: 2
Views: 1082

Re: '29 AA running boards

Dad in law made his own. Simply cut to size and weld on the frame around it. Put on the rubber pads on top after paint and they look very good. All depends how handy you are and how fussy you are. If you can weld and get the material "cheep", give it a try. Good luck..
by KimVanOrder
November 30th, 2014, 6:49 pm
Forum: AA Ford Discussion
Topic: Carburetor
Replies: 11
Views: 1645

Re: Carburetor

I see no need to. Think about it. The gas in the carb. is no more likely to go bad or do any damage than the gas that is in your tank, or in your family car. If you were going to leave it for the entire season. Well, I still wouldn't. I leave the gas in all my small engines year around and never hav...
by KimVanOrder
November 27th, 2014, 6:48 pm
Forum: AA Ford Discussion
Topic: 1930 AA Radiator question
Replies: 5
Views: 1670

Re: 1930 AA Radiator question

Look into the recore route. That way you will know it fits. and you can select the cooling capacity of the new one.
by KimVanOrder
November 27th, 2014, 6:44 pm
Forum: AA Ford Discussion
Topic: Worm gear swap.
Replies: 2
Views: 961

Re: Worm gear swap.

thanks for your input. It is a great help. I need to do a bunch of reseach on the Lincoln Over / Under drive and decide if I should try to put it in while I have the rear end out. If I remember it is 25% overdrive. With the higher rear gears and the overdrive I start to think of just how much torque...
by KimVanOrder
November 22nd, 2014, 5:12 pm
Forum: AA Ford Discussion
Topic: Worm gear swap.
Replies: 2
Views: 961

Worm gear swap.

Anyone interested in posting a step by step disortation on how to swap low speed worm and ring gear for High speed. I have the low speed in the truck and the high speed laying on the bench. Also I have a Lincoln Over/ under drive. What will it take to install that? Different drive shaft and tube?
by KimVanOrder
November 22nd, 2014, 5:07 pm
Forum: AA Ford Discussion
Topic: Who'd be interested
Replies: 22
Views: 4128

Re: Who'd be interested

I'm interested! Sounds like your planning on making exactly what I need. (Boy that word "Need" can get you in trouble)!

Where are you at and how much?

KVO
by KimVanOrder
November 22nd, 2014, 5:00 pm
Forum: AA Ford Discussion
Topic: Windshield hinge gasket installation
Replies: 3
Views: 898

Re: Windshield hinge gasket installation

Thanks Bob. I got it now. Will continue to clean up parts, Fill, prime, and paint. Seams like an never ending task. Lots of snow so I guess it is ok to spend time in the shop.. :)

kvo
by KimVanOrder
November 22nd, 2014, 7:36 am
Forum: AA Ford Discussion
Topic: Windshield hinge gasket installation
Replies: 3
Views: 898

Windshield hinge gasket installation

How dose the windshield Hinge gasket go in. I saw somewhere that it goes between the hinge and the header? But how? where dose the round end go?
Any help would be appreciated.

Thanks in advance.

KVO
by KimVanOrder
November 15th, 2014, 4:12 pm
Forum: AA Ford Discussion
Topic: Can anyone tell me the shift speeds for the 4-speed?
Replies: 5
Views: 1571

Re: Can anyone tell me the shift speeds for the 4-speed?

I don't know if there is a "recomended" speed. I'd just rev it up and shift. :shock: Do it by ear. Soon as things start to sound really wound up, SHIFT!!! (your ground speed will be slow with the low rear end gears you have). :wink:
by KimVanOrder
November 15th, 2014, 4:08 pm
Forum: AA Ford Discussion
Topic: Frt. Windshield gaskets mounting
Replies: 1
Views: 755

Frt. Windshield gaskets mounting

I've got a '28 with what I think is a '30 windshield in it. Also have the windshield gasket set for a "28 Briggs". Is that the correct seals? And how dose the gasket / Seal mount in the windshield frame? Anyone have a cross section drawing of it?

Thanks in advance for any help..

KVO