Hello HKDude,
Attached are truck speeds at various engine rpm's for the high and low speed gears for '28/'29.
Search found 3062 matches
- November 28th, 2006, 7:26 am
- Forum: AA Ford Discussion
- Topic: Top Speed - 7.25 Axle
- Replies: 3
- Views: 3730
- November 26th, 2006, 10:24 am
- Forum: AA Ford Discussion
- Topic: express fenders
- Replies: 4
- Views: 4708
- November 26th, 2006, 8:22 am
- Forum: AA Ford Discussion
- Topic: express fenders
- Replies: 4
- Views: 4708
Hello modeleh, Your 1930 AA with 82-B cab (round style) would have an 89-A express body and single rear wheel only. All express trucks TT and AA came with rear fenders. The AA express had long running boards and aprons and the rear fenders are unique to the AA express, platform, and panel delivery a...
- November 22nd, 2006, 9:22 am
- Forum: AA Ford Discussion
- Topic: Truck Flatbed Frame - Wood Sill - Truck Frame Does Not Align
- Replies: 3
- Views: 3372
Wayne, FYI The AA131.5 chassis has a tapered frame for all of 1931. And, the corresponding platforms bodies for these frames all had tapered sills. Only the AA157 for 1931 had parallel side frame members and the corresponding platform had parallel sills. The 1932 platform for the BB131.5 chassis had...
- November 18th, 2006, 7:28 am
- Forum: AA Ford Discussion
- Topic: Door repair advice needed. ( 82A cab )
- Replies: 3
- Views: 3088
I saw a couple of '28-mid '30, 82-A closed cab doors which were repaired by a local hot rod shop. They made patch pieces for the hinge areas and welded the pieces in. The end product look great. I am interested in hearing from Richard how he would go about fixing this area if the door. The hot rod s...
- November 18th, 2006, 7:17 am
- Forum: AA Ford Discussion
- Topic: New AA owner here
- Replies: 5
- Views: 4645
- November 17th, 2006, 10:24 am
- Forum: AA Ford Discussion
- Topic: New AA owner here
- Replies: 5
- Views: 4645
- November 14th, 2006, 7:07 am
- Forum: AA Ford Discussion
- Topic: Stake Body Drawings
- Replies: 1
- Views: 5464
Araon, The Ford Model AA Truck Club, April 1997 newsletter has a 20 page article covering the 88-A platform including information on the wood sills and floor boards, mounting hardware, and spare wheel carriers. The 88-A was the Ford specified body model number. This body was used from the beginning ...
- November 11th, 2006, 1:19 pm
- Forum: AA Buy and Sell
- Topic: STRAWPOLL - NEW GEAR SETS
- Replies: 3
- Views: 3158
Hello Alan, When you talk about the bevel gear units, are you talking about the '29 bevel gear axle or the '30/'31 bevel gear axle? And, I would think that there would be more interest in these gears with a better ration than the original high speed. A ratio of 4.11:1 would yield a speed of 54 mph a...
- November 11th, 2006, 11:03 am
- Forum: AA Buy and Sell
- Topic: WANTED: Worm drive pinion gear set
- Replies: 13
- Views: 8053
- November 9th, 2006, 1:45 pm
- Forum: AA Buy and Sell
- Topic: WANTED: Worm drive pinion gear set
- Replies: 13
- Views: 8053
- November 9th, 2006, 10:04 am
- Forum: AA Buy and Sell
- Topic: WANTED: Worm drive pinion gear set
- Replies: 13
- Views: 8053
- November 2nd, 2006, 5:24 pm
- Forum: AA Ford Discussion
- Topic: Front Spring Perch
- Replies: 3
- Views: 3513
Brian, You most likely need to use a press to remove the spring perch. They can be very difficult to remove. I have used a combination of a press and heat to remove spring perches. Reproduction AA spring perches are not available. So, you must find good original AA spring perches or fix the ones you...
- October 31st, 2006, 7:45 pm
- Forum: AA Ford Discussion
- Topic: Seat support board
- Replies: 5
- Views: 4088
- October 31st, 2006, 4:24 pm
- Forum: AA Ford Discussion
- Topic: Seat support board
- Replies: 5
- Views: 4088
Hello Richard, I am fairly sure that the board can be forced into place after the seat riser is riveted to the floor pan. But I am not sure. So, it might be best to have it so you can test this out before hand. If yes, then I would get primer on the floor pan where the board goes before installation...