Search found 1442 matches

by Bob C
March 4th, 2022, 10:31 am
Forum: AA Ford Discussion
Topic: AA Frame Welt
Replies: 2
Views: 3660

Re: AA Frame Welt

Since the AA frame is the same width as the A frame until a few inches behind the
rear motor mount and most of the splash apron does not sit on the frame I don't
see any need for 2" welt.
by Bob C
February 27th, 2022, 1:01 pm
Forum: AA Ford Discussion
Topic: Early 1928 AA floor mats
Replies: 12
Views: 11255

Re: Early 1928 AA floor mats

You should order the drawings for the mat from Ford.
https://www.thehenryford.org/collection ... arch/about
You can get the EI number from the MAFFI site.
https://www.maffi.org/WSContent/Parts.html
by Bob C
February 24th, 2022, 4:32 pm
Forum: AA Ford Discussion
Topic: Early 1928 AA floor mats
Replies: 12
Views: 11255

Re: Early 1928 AA floor mats

Maybe contact some of the vendors and also post his on Ford Barn and Vintage Ford Forum.
https://www.fordbarn.com/forum/forumdisplay.php?f=3

https://www.vintagefordforum.com/forum/model-a
by Bob C
February 14th, 2022, 4:22 pm
Forum: AA Ford Discussion
Topic: Spring perches
Replies: 14
Views: 20179

Re: Spring perches

Model A perches won't work on AA.
by Bob C
February 12th, 2022, 4:25 pm
Forum: AA Ford Discussion
Topic: AA Universal Joint
Replies: 8
Views: 5961

Re: AA Universal Joint

The 10x10 goes between the jack shaft and drive shaft on 1930-31.
by Bob C
February 11th, 2022, 1:28 pm
Forum: AA Ford Discussion
Topic: Headlight switch kit installation
Replies: 4
Views: 5450

Re: Headlight kit installation

These pictures may help.
DCP_1141.JPG
DCP_1141.JPG (107.26 KiB) Viewed 5420 times
A-Switch.jpg
Most of the parts won't fit without some work. The U-clip will probably need filing, the spider may not fit on the horn rod and the
horn rod may need sanding to fit in the steering shaft.
by Bob C
January 12th, 2022, 3:22 pm
Forum: AA Ford Discussion
Topic: Floor Board Anti-squeak Webbing
Replies: 2
Views: 2437

Re: Floor Board Anti-squeak Webbing

The Standards say "No webbing was used on the mating edges of either board."
by Bob C
December 22nd, 2021, 8:26 am
Forum: AA Ford Discussion
Topic: Piston Orientation during installation, Left or Right hand?
Replies: 4
Views: 4332

Re: Piston Orientation during installation, Left or Right hand?

The original pistons had a arrow pointing to the front of the engine.
1931_03-fig_1121.png
by Bob C
December 9th, 2021, 9:26 am
Forum: AA Ford Discussion
Topic: Running board length
Replies: 13
Views: 8340

Re: Snyders antiquauto

Here you go.
AA-running-board.jpg
by Bob C
December 7th, 2021, 11:57 am
Forum: AA Ford Discussion
Topic: Running board length
Replies: 13
Views: 8340

Re: Snyders antiquauto

the thing is, I don’t know how long it should be. I need to know the length of the running boards on a Ford aa track 1931 1.5 t car. Can anyone measure the length of these footboards on their car with a tape measure? in centimeters or inches Neil gave you a link with all the measurements on 12-6-20...
by Bob C
December 5th, 2021, 8:11 am
Forum: AA Ford Discussion
Topic: Running board length
Replies: 13
Views: 8340

Re: Snyders antiquauto

Snyder's web site and Reds34 have both stated the running boards are 29 1/2 inches long.
by Bob C
October 1st, 2021, 9:03 am
Forum: AA Ford Discussion
Topic: Floating motor mounts
Replies: 12
Views: 8615

Re: Floating motor mounts

I did a quick measurement and it looks like if you use an "A" rear mount in
a "AA" the engine will be one inch lower at the rear mount.
by Bob C
September 29th, 2021, 3:54 pm
Forum: AA Ford Discussion
Topic: Drive shaft issue
Replies: 2
Views: 3375

Re: Drive shaft issue

There should be a couple of pins holding the coupling to the driveshaft and pinion gear.
DSC07822.JPG
by Bob C
September 27th, 2021, 7:51 am
Forum: AA Ford Discussion
Topic: rear axle of the car Ford AA 1931
Replies: 6
Views: 5706

Re: rear axle of the car Ford AA 1931

[/quote]

Or find another housing. I picked best parts from three axles to assemble mine.
[/quote]

He is in the Ukraine, may be hard to find there.