Search found 179 matches

by mikeg
January 24th, 2003, 10:02 am
Forum: AA Ford Discussion
Topic: I'll get the ball rolling. AA bearings
Replies: 6
Views: 8210

Re: Dual High

Mike- For now I'd like to find a jackshaft assembly to put in there and keep the truck on the road until I can afford an overdrive or find a warford. Vince Falter just posted a blowup on AHOOGA of the unit. Tim. Tim, Here is a picture of the driveshaft I have for a 30 swb truck. http://www.aa-fords...
by mikeg
January 23rd, 2003, 12:52 pm
Forum: AA Ford Discussion
Topic: Picture of my SWB 30 AA
Replies: 0
Views: 3956

Picture of my SWB 30 AA

Found a "pre-disassembly" pictrure of my 30 SWB, this truck provided a lot of excellent condition parts for my current M30 LWB truck restoration.

Image
by mikeg
January 23rd, 2003, 11:09 am
Forum: AA Ford Discussion
Topic: CC Sheet Metal Question
Replies: 0
Views: 3853

CC Sheet Metal Question

The following picture shows the floor of a CC truck, I'm looking for the rear section outlined in yellow. Is that sheetmetal available from any supplier?

Image
by mikeg
January 22nd, 2003, 12:44 pm
Forum: AA Ford Discussion
Topic: Firewall removal and replacement question
Replies: 2
Views: 5060

Firewall removal and replacement question

I'm planning on transplanting my mid 30's firewall and gas tank with a late 31 indented firewall and gas tank. What is the best method for removing the firewall? Grind the rivets off the various braces, or drill the heads off? Also, when re-installing, is this a cold riveting operation or hot? I not...
by mikeg
January 21st, 2003, 9:48 am
Forum: AA Ford Discussion
Topic: I'll get the ball rolling. AA bearings
Replies: 6
Views: 8210

Re: Dual High

Mike- I just have gone through my dual high unit due to leaking seals. No one that I could find knew anything about the units. The front and rear bearings are the same as far as I can tell, as are the seals. It's kind of odd that the front bearing is lubricated by the U-joint grease and the back be...
by mikeg
January 17th, 2003, 4:14 pm
Forum: AA Buy and Sell
Topic: Budd Wheels Wanted
Replies: 3
Views: 6045

Re: Budd Wheels Wanted

Bradshaw wrote:I'm looking for 2 Budd 5 spoke wheels. I need the "smooth face" wheels without the raised re-inforcement area for the lug nuts.

Thanks
I'll look in my pile of wheels for the type you are looking for, shipping may be spendy though, looks like you are on the east coast?
by mikeg
January 16th, 2003, 4:18 pm
Forum: AA Ford Discussion
Topic: Thanks for setting up AA message board
Replies: 3
Views: 5959

I'm in the process of building an early 30 AA semi. Anyone out there have an AA semi? I have questions about trailer brakes. I have a fuel tanker semi trailer that I'm restoring for it. Hi, this forum works a little differently than Dales WWWboard, your best bet would be to start a new topic titled...
by mikeg
January 16th, 2003, 4:13 pm
Forum: AA Ford Discussion
Topic: I'll get the ball rolling. AA bearings
Replies: 6
Views: 8210

Re: I'll get the ball rolling. AA bearings

AA fans, I have recently gone through the process of finding some bearings for the rear wheel of my '28 truck, and found out that it is not as easy as when I ordered parts for my Model A cars. I will share what I have learned about sources, but I would like to know what other folks have found about...
by mikeg
January 16th, 2003, 7:26 am
Forum: AA Ford Discussion
Topic: Thanks for setting up AA message board
Replies: 3
Views: 5959

Re: Thanks for setting up AA message board

Mike Green. Hope this new AA message board does good. I'm working my way through an early '28 stakebed AA, and have found that specific info and parts for the AA can be difficult to obtain. Hope this board can start to fill the gap Mike Taylor Mike, visit the AA Truck Site at http://www.aa-fords.co...
by mikeg
January 15th, 2003, 7:43 pm
Forum: AA Ford Discussion
Topic: Looking for the following AA parts
Replies: 4
Views: 5707

Looking for the following AA parts

I'm looking for the rear axle bumper pads AA-5783 and the speedo driven gear AA-17271-H, this gear has 13 teeth and a square cable hole.

I'm also looking for the late 31 indented firewall fuel shutoff valve, and associated fuel line and carb mounted filter.
by mikeg
January 15th, 2003, 7:31 pm
Forum: AA Ford Discussion
Topic: AA Forum
Replies: 1
Views: 4080

Re: AA Forum

Hi Mike, Thought I'd try your new forum, I'll keep an eye on it, good luck.. Tom Tucker Blaine, Wash. Hi Tom, Did that AA up your way ever sell? I was thinking of checking that out but I knew better because I would have probably bought it! I'm up to 3 trucks now, your SWB 30 has been very useful in...
by mikeg
January 15th, 2003, 7:27 pm
Forum: AA Ford Discussion
Topic: Glad to see an AA truck discussion page
Replies: 1
Views: 4255

Re: Glad to see an AA truck discussion page

Mike , Just a wish of good luck in your new endeavor. How about a link to The Antique Truck Club of America , (ATCA) or The American Truck Historical Society (ATHS)? Steve Skurnowicz Hi Steve, I'll do a search and see what I come up with, if I don't find the websites I'll probably ask for the URL's...
by mikeg
January 15th, 2003, 5:25 pm
Forum: AA Ford Discussion
Topic: AA Restoration pictures?
Replies: 6
Views: 6065

AA Restoration pictures?

Does anybody have pictures of their AA truck or restoration project online? If you have a website I would like to add it to my AA Truck links page. If you don't have a website I would be happy to create a space for you on my server.

Just shoot me an email and I'll take care of the rest.
by mikeg
January 15th, 2003, 5:06 pm
Forum: AA Ford Discussion
Topic: Welcome to the AA Fords Discussion Forum!
Replies: 0
Views: 72266

Welcome to the AA Fords Discussion Forum!

Hello AA owners!

Welcome to the AA Ford discussion forums. This system was setup for you, so please feel free to let me know what you would like to see here.

The rules are simple:

1) Have fun
2) Respect others

Again, welcome to the AA Fords Forum! :D