Search found 161 matches

by JPP
December 22nd, 2014, 11:36 am
Forum: AA Ford Discussion
Topic: Rear leaf spring forward link bolt
Replies: 18
Views: 11494

Rear leaf spring forward link bolt

I am trying to determine the pitch of the forward shackle 3/4 nut. This is the lower bolt as the top bolt does not have a nut. And yes this is not the center pivot bolt, as I believe that is much bigger. So I tried a 3/4 16, not sure if this is the one, snug to start. Help.
by JPP
November 24th, 2014, 8:20 am
Forum: AA Buy and Sell
Topic: 28 hubcaps replated
Replies: 6
Views: 5021

Re: 28 hubcaps replated

I will Never quit looking for hub caps that cost less than my entire wheel!
by JPP
November 8th, 2014, 2:09 pm
Forum: AA Club House
Topic: Copies from Japan
Replies: 4
Views: 7093

Copies from Japan

Turns out Henry went to Japan to built a plant in 1932, which lasted till 1945 for obvious reasons. I just went to Nissan Car museum and was taken by the striking resemblance to the Ford Motor and Car, al be it smaller.
Datsun.jpg
Datsun.jpg (45.65 KiB) Viewed 7093 times
by JPP
October 23rd, 2014, 11:44 am
Forum: AA Ford Discussion
Topic: Spindle stamping
Replies: 9
Views: 6023

Re: Spindle stamping

So I know I have seen Ford Trucks on TT flatbeds, but I am not sure if they were made by Ford, so is this the first time ford put the words TRUCK on their vehicles, just a fun thought. I am sure Neil knows..
by JPP
October 23rd, 2014, 8:27 am
Forum: AA Ford Discussion
Topic: Spindle stamping
Replies: 9
Views: 6023

Spindle stamping

All, I was just replacing king pin bushings and noticed that the spindle bracket said TRUCK on the back of it. Is this the only place Ford used the word Truck on my 29 AA? Just a thought.
spindle.jpg
spindle.jpg (157.6 KiB) Viewed 6023 times
by JPP
September 30th, 2014, 11:28 am
Forum: AA Ford Discussion
Topic: Timken numbers
Replies: 17
Views: 10959

Re: Timken numbers

Kekel, Allen R. <allen.kekel from TIMKEN Wow, had to work for my paycheck today! I actually found a very old catalog in our archives, printed in 1933, where it shows the bearings for your application. Attached is a photocopy of the page with your application. To answer your question, yes those are t...
by JPP
September 19th, 2014, 4:14 am
Forum: AA Ford Discussion
Topic: Timken numbers
Replies: 17
Views: 10959

Re: Timken numbers

AA 1202.
by JPP
September 18th, 2014, 4:44 am
Forum: AA Ford Discussion
Topic: Timken numbers
Replies: 17
Views: 10959

Re: Timken numbers

The race is too small for the hub.
by JPP
September 17th, 2014, 9:50 am
Forum: AA Ford Discussion
Topic: Timken numbers
Replies: 17
Views: 10959

Re: Timken numbers

Bob, Thanks for the info. To be clear, I don't know if my front end is an early 30 or '29, but I will take a picture and post it. What I do know is that the picture of the bearing on this thread came off my truck and as you can see it is stamped aa1201. When I recently received the Timken 1680 repla...
by JPP
September 17th, 2014, 4:40 am
Forum: AA Ford Discussion
Topic: Timken numbers
Replies: 17
Views: 10959

Re: Timken numbers

Ok, so I ordered the AA1201 bearing or Timken 1680, and the bearing does not fit, it is too small. While my bearing is broken, the inner race of the aa1201 has the following markings, is AA 1201 M M different from AA1201 AR
by JPP
September 15th, 2014, 3:46 pm
Forum: AA Ford Discussion
Topic: Timken numbers
Replies: 17
Views: 10959

Re: Timken numbers

Bob, thanks
by JPP
September 15th, 2014, 2:32 pm
Forum: AA Ford Discussion
Topic: Timken numbers
Replies: 17
Views: 10959

Timken numbers

I have a 29 and the AA numbers for inner :cry: cone bearing and cup are 1201 &1202 and the outer bearings and cup is 1216 &1217. Does anyone know the correct Timken numbers, apparently Mac's does not.
by JPP
September 13th, 2014, 8:19 am
Forum: AA Buy and Sell
Topic: 29 front wheel castle nut
Replies: 2
Views: 2802

29 front wheel castle nut

Hey, I lost front wheel bearing and as the wheel kept turning gauged out my retaining castle nut.. looking to buy one, anyone have a spare? Or direct me to a source. Thanks.
by JPP
September 1st, 2014, 5:18 am
Forum: AA Club House
Topic: A Sad Story
Replies: 10
Views: 62065

Re: A Sad Story

John, glad to see your fine. I too am in mass, if I can help just ask..
by JPP
May 29th, 2014, 4:34 pm
Forum: AA Ford Discussion
Topic: Mail/map pouches
Replies: 17
Views: 9335

Re: Mail/map pouches

Ok, I am good with the rivets but how do I screw the top of the pocket in, not a lot of room. What is the wood for? Decoration?