Search found 1148 matches

by Bob C
November 13th, 2009, 6:17 pm
Forum: AA Ford Discussion
Topic: 29 AA motor mounts
Replies: 12
Views: 1217

Re: 29 AA motor mounts

The service bulletin says the mount is thicker not wider and the bolts from the
old mount will be to short.
by Bob C
October 27th, 2009, 10:06 am
Forum: AA Ford Discussion
Topic: gearlever
Replies: 6
Views: 1129

Re: gearlever

There is a reverse lockout lever on Ebay right now item 270474170128.
by Bob C
October 13th, 2009, 10:05 am
Forum: AA Buy and Sell
Topic: 5:14 speedo drive gear
Replies: 13
Views: 1157

Re: 5:14 speedo drive gear

I had to find a AA gear, the BB drive line is bigger from the trans u-joint
back to the pinion gear.
by Bob C
October 12th, 2009, 10:26 pm
Forum: AA Buy and Sell
Topic: 5:14 speedo drive gear
Replies: 13
Views: 1157

Re: 5:14 speedo drive gear

Russ,
That one looks OK. If it spins on the splines when you put it on the drive shaft
it is probably off a BB. Somebody put a BB one on my AA and it would just spin on the
spline as the BB splines are bigger.
by Bob C
October 11th, 2009, 7:38 pm
Forum: AA Ford Discussion
Topic: Ford truck restoration
Replies: 26
Views: 2919

Re: Ford truck restoration

I have to agree with Keith. I looked in my Canadian parts book and
the rear end and the hub caps are the same as on this truck.
by Bob C
October 11th, 2009, 4:41 pm
Forum: AA Ford Discussion
Topic: Chassis and frame coating ?s
Replies: 19
Views: 2420

Re: Chassis and frame coating ?s

Scott
If you have a lot of pitting I would have it sand blasted and then you can putty up the
bad spots and put on some sanding primer and block sand it to look like new.
by Bob C
October 4th, 2009, 3:05 pm
Forum: AA Ford Discussion
Topic: wiring diagram
Replies: 1
Views: 457

Re: wiring diagram

Vince has a wiring diagram on his site under electrical. http://idisk.mac.com/forever4/Public/pa ... iagram.htm
by Bob C
September 30th, 2009, 10:00 am
Forum: AA Ford Discussion
Topic: Need Some Help
Replies: 9
Views: 1954

Re: Need Some Help

The bracket behind the jack stand is where the brake rod return spring goes.
by Bob C
September 20th, 2009, 9:57 am
Forum: AA Ford Discussion
Topic: how much air 650 x20 firestone
Replies: 19
Views: 2897

Re: how much air 650 x20 firestone

I looked in the service bulletins and on page 330 it says 75lb front and 85lb
rear. On page 410 45lb front and rear for 6.00X20 and 90lb for 32X6 and
to further confuse things on page 456 minimum pressure 6.00X20 45lb and
32X6 80lb.
by Bob C
September 19th, 2009, 11:28 am
Forum: AA Ford Discussion
Topic: try again
Replies: 7
Views: 1034

Re: try again

Tom,
When you say "tighten up the tops" if you mean make the hole for the stud on
the brake operating lever smaller DON'T. That hole needs to be big or you will
never get the stud to go in.
by Bob C
September 13th, 2009, 7:11 pm
Forum: AA Ford Discussion
Topic: HAHA part of the club now.
Replies: 15
Views: 1405

Re: HAHA part of the club now.

Scott, I looked at my 157" frame and the number is farther back on it than you are looking.
mine is directly in line with the bracket with the two holes in it for mounting the cab and close to the inner edge of the frame rail.

Bob
by Bob C
September 11th, 2009, 5:20 pm
Forum: AA Ford Discussion
Topic: Missing something at spring perch?
Replies: 17
Views: 1913

Re: Missing something at spring perch?

Russ, The spring shackles are backwards.
by Bob C
September 9th, 2009, 7:02 pm
Forum: AA Ford Discussion
Topic: HAHA part of the club now.
Replies: 15
Views: 1405

Re: HAHA part of the club now.

I think what somebody did was take the original gear that bolts to the trans output shaft and welded it to a u-joint
and then cut the coupling shaft and welded that to the other end of the u-joint. Looks like you will need a complete
new coupling shaft.
by Bob C
September 8th, 2009, 3:20 pm
Forum: AA Ford Discussion
Topic: HAHA part of the club now.
Replies: 15
Views: 1405

Re: HAHA part of the club now.

Drew, The open coupling shaft I have is totally different than the closed shaft. It has Mechanics 4C wing bearing u-joints and a hollow tube drive shaft. Look at the second picture Scott posted of the drive line. The front u-joint is not a AA, it has needle bearings like the later trucks, looks stra...
by Bob C
September 7th, 2009, 6:26 pm
Forum: AA Ford Discussion
Topic: HAHA part of the club now.
Replies: 15
Views: 1405

Re: HAHA part of the club now.

Scott,
Could you post some pictures of the coupling shaft(the shaft that goes between the transmission and the rear end) and where it connects to the rear end. I have an open coupling shaft but I don't know what they used for a seal.

Thanks Bob