I finally found a deck and cab for my project and brought it home in two loads. I had planned on an Express Bed, but my youngest (who will inherit the rig) Insisted on a rack truck. I am thinking this is a later bed as the rear most stake pockets are internal rather than external. I am short of stakes, and racks, but I may know of a stash not far from me. Here are some pics to show:
This truck also came equipped with the primary secondary U-joints on the coupling shaft:
Strange little Auto greaser on the water pump:
The brakes were pretty schetchy with farmer fixes all over her:
The other mystery is how the block came to be numbered the same as the frame, as the engine is a Diamond block, and I was under the impression they were used in Industrial/Farm unit applications.(Wrong?)
The P/O said this truck had served overseas at one time and she sported some Egyptian writing on the doors. Sadly he did not photo graph the artwork.
I have found Green, Yellow, Baby Blue, Black, and lastly Army Olive drab paint on the cab pieces, so she's had a few previous masters.
The Deck
- Farrell In Vancouver
- Posts: 314
- Joined: February 23rd, 2011, 6:52 am
- Body Type: Deck
- Model Year: 1931
- Location: Vancouver BC Canada
- Neil Wilson
- Posts: 3063
- Joined: February 5th, 2003, 9:42 pm
- Body Type: 82-A/89-A
- Model Year: 1930
- Location: Boulder, CO
- Contact:
Re: The Deck
The platform is a 187-A (based on the dimensions you indicate). This is for the AA131 from 3/31-2/32.
The engine was likely stamped with the original engine ID when replaced. Does the engine ID have the AA prefix and a star on each end?
The engine was likely stamped with the original engine ID when replaced. Does the engine ID have the AA prefix and a star on each end?
Regards, Neil Wilson
______________________________________
aafords.com@gmail.com - use this email for contact
https://aafords.com/
______________________________________
aafords.com@gmail.com - use this email for contact
https://aafords.com/
- rollingsculpture
- Posts: 553
- Joined: December 9th, 2008, 7:30 am
- Body Type: platform
- Model Year: 1931
- Location: Takoma Park maryland
Re: The Deck
lucky find that is a nice unit , put em together !!
-
- Posts: 1446
- Joined: April 24th, 2003, 11:50 am
- Body Type: Mail truck, Stake tr
- Model Year: 1931
- Location: SO CAL
Re: The Deck
Never seen a pressed steel bearing retainer on the transmission like that.
Bob
Bob
-
- Posts: 20
- Joined: March 28th, 2012, 7:13 pm
- Body Type: AA stake bed
- Model Year: 1930
Re: The Deck
Your stake bed has to be the correct bed for your AA because it will not fit 1932 and later because their frame rails were parallel. Pat Farrell...Sedro Woolley, WA
- Farrell In Vancouver
- Posts: 314
- Joined: February 23rd, 2011, 6:52 am
- Body Type: Deck
- Model Year: 1931
- Location: Vancouver BC Canada
Re: The Deck
I'll get the engine number and frame number next time I am down at the farm.
Also plan to take detailed shots of the bed for restoration work (Man they is a lotta bolts in dat deck!)
I also have not seen that bearing retainer/U-joint housing combo before. I'll take some detailed shots of that for the curious as well.
Is there a source for the six u-bolts securing the bed to the frame?
Seems I did not get them and have not a clue as to what they would look like on this thirty one.
Also plan to take detailed shots of the bed for restoration work (Man they is a lotta bolts in dat deck!)
I also have not seen that bearing retainer/U-joint housing combo before. I'll take some detailed shots of that for the curious as well.
Is there a source for the six u-bolts securing the bed to the frame?
Seems I did not get them and have not a clue as to what they would look like on this thirty one.
- tiredtruckrestorer
- Posts: 338
- Joined: April 20th, 2003, 7:09 pm
- Model Year: 1931
- Location: Orwigsburg, PA
Re: The Deck
I believe the steel adapter in question was used to attach the outer housing of the new BB style removable coupling shaft assembly (as shown in the July 1932 Service Bulletins) to the AA four speed transmission. These coulping shaft assemblies were made available as a service replacement for the AA's so a transmission, clutch or u-joints could be replaced without pulling the engine or the rear end. The BB's had a bigger diameter bolt pattern on the rear of the transmission where the outer housing attaches than the AA's did, thus the need for this adapter. I've found several of these over the years.
Keith
Keith