Open Coupling Shaft
-
- Posts: 1442
- Joined: April 24th, 2003, 11:50 am
- Body Type: Mail truck, Stake tr
- Model Year: 1931
- Location: SO CAL
Open Coupling Shaft
Does anybody have a AA with an open coupling shaft that they could tell
me what type of seal was used at the differential.
me what type of seal was used at the differential.
-
- Posts: 267
- Joined: December 27th, 2008, 9:30 pm
- Body Type: flatbed
- Model Year: 1930
Re: Open Coupling Shaft
Thank you for the photo. It confirmed a different issue for me. Was this open shaft a ford thing or was it an after market idea?
-
- Posts: 1442
- Joined: April 24th, 2003, 11:50 am
- Body Type: Mail truck, Stake tr
- Model Year: 1931
- Location: SO CAL
Re: Open Coupling Shaft
I would say it's after market since it is not in any of the Ford
parts books.
parts books.
-
- Posts: 496
- Joined: April 25th, 2005, 2:25 pm
- Model Year: 1930
- Location: Ojai, California
Re: Open Coupling Shaft
Bob:
The "coupling shaft" is basically an extension in the driveline that links the rear of the transmission to the front of the torque-tube (main driveline). So, I don't see what the coupling shaft would have to do with a seal clear back at the differential. Maybe I don't understand for what info you're asking. Can you be more specific?
-- Drew
The "coupling shaft" is basically an extension in the driveline that links the rear of the transmission to the front of the torque-tube (main driveline). So, I don't see what the coupling shaft would have to do with a seal clear back at the differential. Maybe I don't understand for what info you're asking. Can you be more specific?
-- Drew
Drew Mashburn
-
- Posts: 1442
- Joined: April 24th, 2003, 11:50 am
- Body Type: Mail truck, Stake tr
- Model Year: 1931
- Location: SO CAL
Re: Open Coupling Shaft
Sorry, what I was asking about was what the seal looks like where the coupling shaft enters
the torque tube at the cross member.
the torque tube at the cross member.
- Mike in Maine
- Posts: 188
- Joined: November 17th, 2004, 1:54 pm
- Body Type: 82B
- Model Year: 1931
- Location: Alfred, Maine
Re: Open Coupling Shaft
From a 1930 AA torque tube. Grease retainer nearest the torque tube bell. Does your tube have one or two grease fittings. Just wondering?
- Attachments
-
- torque tube.jpg (62.72 KiB) Viewed 9047 times
-
- Posts: 496
- Joined: April 25th, 2005, 2:25 pm
- Model Year: 1930
- Location: Ojai, California
Re: Open Coupling Shaft
Mike:
Great photo! Hopefully, it'll be of assistance to Bob. Do you have photos that you can post of the gasket that goes under the rear end of the thin metal coupling shaft housing and the front edge of the frame cross-member? And, do you have photos of the inside of the two clam-shells (specifically the recessisons for the seal) that bolt over the front of the torque tube. They also bolt to the backside of the cross-member I just mentioned. I believe Bob would like to see the gasket (seal) that goes inside the clam-shells and the gasket that goes between them and the cross-member. And, the gasket that goes on the front of the same cross-member. Do you know where these gaskets/seals might be purchased?
-- Drew
Great photo! Hopefully, it'll be of assistance to Bob. Do you have photos that you can post of the gasket that goes under the rear end of the thin metal coupling shaft housing and the front edge of the frame cross-member? And, do you have photos of the inside of the two clam-shells (specifically the recessisons for the seal) that bolt over the front of the torque tube. They also bolt to the backside of the cross-member I just mentioned. I believe Bob would like to see the gasket (seal) that goes inside the clam-shells and the gasket that goes between them and the cross-member. And, the gasket that goes on the front of the same cross-member. Do you know where these gaskets/seals might be purchased?
-- Drew
Drew Mashburn
- Robert Gray
- Posts: 102
- Joined: May 8th, 2006, 4:03 pm
- Model Year: 1930
Re: Open Coupling Shaft
Mike, Mine has two grease fittings. Both on drivers side, one just ahead and one just aft of where the speedo connection is on the other side.
Bob
Bob
- Mike in Maine
- Posts: 188
- Joined: November 17th, 2004, 1:54 pm
- Body Type: 82B
- Model Year: 1931
- Location: Alfred, Maine
Re: Open Coupling Shaft
Drew, I copied this from Ford Service Bulletin of January 1930, page 415. It is a cross section which may be of more help. The felts can be purchased from most vintage parts suppliers. I bought mine from Bratton's. Hope this is what you had in mind.
Mike
Mike
- Attachments
-
- COUPLER.jpg (91.24 KiB) Viewed 9005 times
- Mike in Maine
- Posts: 188
- Joined: November 17th, 2004, 1:54 pm
- Body Type: 82B
- Model Year: 1931
- Location: Alfred, Maine
Re: Open Coupling Shaft
Bob, I was interested in whether one or two grease fittings because a change was made in June 1930.
One fitting was added ahead ( toward xmbr ) of the other fitting to assure more grease was getting to the u-joint. Hope all is well with you and progress is being made.
Mike
One fitting was added ahead ( toward xmbr ) of the other fitting to assure more grease was getting to the u-joint. Hope all is well with you and progress is being made.
Mike
-
- Posts: 1442
- Joined: April 24th, 2003, 11:50 am
- Body Type: Mail truck, Stake tr
- Model Year: 1931
- Location: SO CAL
Re: Open Coupling Shaft
The seal I am asking about would only be used on the after market open coupling shaft.
There is a mark on the after market yoke from a seal. I assume there was some type of plate
with a seal in it to keep dirt out of the torque tube.
There is a mark on the after market yoke from a seal. I assume there was some type of plate
with a seal in it to keep dirt out of the torque tube.
-
- Posts: 496
- Joined: April 25th, 2005, 2:25 pm
- Model Year: 1930
- Location: Ojai, California
Re: Open Coupling Shaft
I have seen those open driveshafts on Russian AA trucks. There is no torque tube. The driveshaft is completely open from the transmission intermediate shaft all the way to the diferential. There were no rear radius rods on those trucks either, and the brakes were hydraulic. The torque tube has to be in place in order for the radius rods to be used to hold the rear brake and emergency brake actuator levers in place, unless a special bracket was made for the brake levers on trucks that used rod brakes without the torque tube. I don't have any other information on part numbers or special part applications, other than to say that parts do exist to accomplish a completely open driveshaft on an AA. The Russian AA trucks originally came with torque tube and all other parts like the USA made AA. The open driveshaft trucks have been modified.
Re: Open Coupling Shaft
In the July 1932 Ford Service Bulletins page 35 fig.51 is a drawing of a coupling shaft that appears to be open for the AA truck. This was a new part for the previous model. Might be worth a look.
Hayslip