We are preparing to install new tires, tubes and liners on the front of the fire engine. Do the bent valve stems point inward or outward on the wheels?? It seems outward would be easier to reach.
Thanks!!
Bob Campbell
Installing tubes in AA tires
- Bob from Northport
- Posts: 21
- Joined: September 2nd, 2010, 8:49 pm
- Body Type: 29 Fire engine
- Model Year: 1929
- Location: Northport, Michigan
Installing tubes in AA tires
Bob's Model A Ford Garage
Northport, Michigan
- spectria
- Posts: 1874
- Joined: May 15th, 2008, 9:53 pm
- Body Type: Mail Truck, Stakebed
- Model Year: 1931
- Location: Quincy, Ca.
Re: Installing tubes in AA tires
The stems point out, so on duallys the outer rear wheel stem points in, Hence the dual sided filler tip.
Be very cautious of filling split rims with air. You may already know about the dangers, but if you don't say so and we will fill you in... There are specific things you need to do to be safe. Sry if you already know...
Be very cautious of filling split rims with air. You may already know about the dangers, but if you don't say so and we will fill you in... There are specific things you need to do to be safe. Sry if you already know...
Dave in Quincy, Ca. I love Pics!!!! Post them All!!!
Join the Ford Model AA Truck Club - membership form at http://www.fmaatc.org
Join the Ford Model AA Truck Club - membership form at http://www.fmaatc.org
-
- Posts: 474
- Joined: September 24th, 2009, 3:06 pm
- Body Type: Express
- Model Year: 1928
- Location: NE Illinois
Re: Installing tubes in AA tires
I put mine to the inside for safety sake. Also when I aired them up I wrapped three nylon ratchet type slings around them to keep them together. Be careful.
- Neil Wilson
- Posts: 3062
- Joined: February 5th, 2003, 9:42 pm
- Body Type: 82-A/89-A
- Model Year: 1930
- Location: Boulder, CO
- Contact:
Re: Installing tubes in AA tires
The '28/'29 AA's originally had straight stems. The attached shows the Schrader hardware. The '30/'31 AA's originally had a double bent stems. The stems point toward the wheel center but upwards.
- Attachments
-
- x28-29 AA Tube Valve Hardware 3 - Schrader.jpg (57.63 KiB) Viewed 2856 times
Regards, Neil Wilson
______________________________________
aafords.com@gmail.com - use this email for contact
https://aafords.com/
______________________________________
aafords.com@gmail.com - use this email for contact
https://aafords.com/
- spectria
- Posts: 1874
- Joined: May 15th, 2008, 9:53 pm
- Body Type: Mail Truck, Stakebed
- Model Year: 1931
- Location: Quincy, Ca.
Re: Installing tubes in AA tires
Yep, what Neil said... BTW Neil did you get my note in the mail, only sent thursday, but I just wondered...
Dave in Quincy, Ca. I love Pics!!!! Post them All!!!
Join the Ford Model AA Truck Club - membership form at http://www.fmaatc.org
Join the Ford Model AA Truck Club - membership form at http://www.fmaatc.org
-
- Posts: 119
- Joined: October 1st, 2007, 6:38 pm
- Model Year: 1930
Re: Installing tubes in AA tires
I use the same type of air nozzle to fill tires. One change that I made was to remove the short rubber hose and replace it with a 10' hose. On the end of the hose, I attached a filler nozzle that clamps to the valve stem. That way if the tire blows I am a few feet away rather than having my face at the tire.
John
NNY
John
NNY