AA wish bone
- gunmetal
- Posts: 304
- Joined: August 21st, 2010, 7:28 am
- Body Type: 188-A
- Model Year: 1929
- Location: Milford, Indiana
AA wish bone
If a wish bone ball is wore down but still in solid working shape, its ok to use as is with rubber boot.
- tiredtruckrestorer
- Posts: 338
- Joined: April 20th, 2003, 7:09 pm
- Model Year: 1931
- Location: Orwigsburg, PA
Re: AA wish bone
Hello Gunmetal,
Moving the wishbone ball up and down, such as using the rubber ball on it, can change the front axle caster. May change the way the truck steers and handles.
Keith
Moving the wishbone ball up and down, such as using the rubber ball on it, can change the front axle caster. May change the way the truck steers and handles.
Keith
-
- Posts: 10
- Joined: May 16th, 2011, 11:31 am
- Body Type: AA
- Model Year: 1930
- Location: Richmond Ky
Re: AA wish bone
I have used a spacer type washer with good luck if the ball is not worn too bad.also they make a replacement radius rod socket that takes up some of the slack. Good luck
.......Dave
.......Dave
-
- Posts: 10
- Joined: May 16th, 2011, 11:31 am
- Body Type: AA
- Model Year: 1930
- Location: Richmond Ky
Re: AA wish bone
I have used a spacer type washer with good luck if the ball is not worn too bad.also they make a replacement radius rod socket that takes up some of the slack. Good luck
.......Dave
.......Dave
- captain marty
- Posts: 208
- Joined: May 13th, 2009, 6:58 pm
- Body Type: firetruck
- Model Year: 1928
- Location: Tulsa
Re: AA wish bone
I’m working on my 28 radius ball (wishbone) also. I’ve read that the ball should be kept as close as possible to the top cap; this keeps your front caster setting where it should be. Adjustment can be made on the bottom cap. You can form a shim from a thin fender washer and insert it in between the ball and bottom cap.
Marty
Marty
-
- Posts: 112
- Joined: November 9th, 2009, 9:22 pm
- Body Type: 185-A
- Model Year: 1930
Re: AA wish bone
not to sound rude, but why not just weld/braze it up, and file/grind it to shape? THere isnt that much load to worry about heat fatuige from welding.
-
- Posts: 112
- Joined: November 9th, 2009, 9:22 pm
- Body Type: 185-A
- Model Year: 1930
Re: AA wish bone
On another note, 1/8" of wear can probably barely make 1* change at the axle at 4' away. I am however all for getting things as snug as they should be. Loose steering is dangerous and sketchy to say the least.(Been there and done that)
- tiredtruckrestorer
- Posts: 338
- Joined: April 20th, 2003, 7:09 pm
- Model Year: 1931
- Location: Orwigsburg, PA
Re: AA wish bone
According to my 1930 Bear Alignment Manual, the '28-'29 AA's only had a 1 degree caster to start with, not 5 degrees like the
A chassis. In November 1929, according to Ford Service Bulletins, the radius rods were lengthened 3/16 of a inch. This small increase in length changed the caster to 3 degrees. This was done to make the truck easier handling. The '30-'31 spec for the heavier front end further increased the caster to 3 1/2 degrees. On a '28-'29 truck, if you are only starting with a 1 degree caster to start with, a worn ball can reduce this down close to zero. Just trying to show that a small of amount wear can cause a harder steering truck.
Keith
A chassis. In November 1929, according to Ford Service Bulletins, the radius rods were lengthened 3/16 of a inch. This small increase in length changed the caster to 3 degrees. This was done to make the truck easier handling. The '30-'31 spec for the heavier front end further increased the caster to 3 1/2 degrees. On a '28-'29 truck, if you are only starting with a 1 degree caster to start with, a worn ball can reduce this down close to zero. Just trying to show that a small of amount wear can cause a harder steering truck.
Keith