4-speed floor plate

Farrell In Vancouver · July 8th, 2013, 10:51 am

Has anyone got a survivor floor plate for the 30-31 4 speed?
I need dimensions and/or a picture as none of my parts trucks came with one, and I've just finished my floor boards so it would be nice to finish this area off.

Also wondering what everyone is using for a floor mat for the AA trucks.

modeleh · Post by **modeleh** » July 8th, 2013, 9:40 pm

Just had a look through my junk, thought I had one, but can't seem to find it. Any other parts you need? I have some spare wheels, a rad, a transmission with pto, front bumper, and some other stuff. I will have another look for the plate tomorrow.

Farrell In Vancouver · Post by **Farrell In Vancouver** » July 9th, 2013, 6:31 am

Thanks for taking a look. I may be looking for a rad, I won't know until I get this truck on the road.
Still curious abot the shape and form on the floor plate.
I could just bend one up and hope its close...........

Brady · Post by **Brady** » July 9th, 2013, 9:18 am

Hello Farrell: I have the 4sp shift tower and e-brake cover plate you're looking for. It was on a fire department doodlebug that I bought back in '02. I gave the chassis away, so you might as well have the plate. I'll send it to you if I can get your address. E-mail: tractorbuggys@yahoo.com - or 607-336-5725. Frank Brady

rollingsculpture · Post by **rollingsculpture** » July 10th, 2013, 7:32 am

made my own plate , also the rubber mat for the car works fine , it will stretch a little on the parking brake handle but sits flat to the floor . i did not cut any of the rubber.

blgitn · Post by **blgitn** » July 10th, 2013, 7:43 am

Nice work!

dan plantz · Post by **dan plantz** » July 25th, 2013, 3:17 pm

Would like to know where i can obtain wood floor pieces for a mid 1929 AA truck with the cutout for the hi-lo food pedals. tks for info

1crosscut · Post by **1crosscut** » July 25th, 2013, 5:35 pm

dan plantz wrote:Would like to know where i can obtain wood floor pieces for a mid 1929 AA truck with the cutout for the hi-lo food pedals. tks for info

I don't believe anyone is reproducing those. I made some for my truck a while back. I could get you a tracing of them if you want to make your own.
Here is a link to the discussion on making them.
http://forums.aa-fords.com/viewtopic.ph ... =dove+tail
Dave

macswoods · Post by **macswoods** » July 26th, 2013, 11:16 am

Like your floor plate. But I could 't make out the measurements for the cutout for the emergency brake handle. Thanks, this happens when "I" got old. Mac.......

spectria · Post by **spectria** » July 27th, 2013, 1:08 am

macswoods wrote:Like your floor plate. But I could 't make out the measurements for the cutout for the emergency brake handle. Thanks, this happens when "I" got old. Mac.......

look here for better pics...
http://forums.aa-fords.com/viewtopic.php?f=1&t=4081

jtw · Post by **jtw** » July 31st, 2013, 5:34 pm

I never get to talk about my nos parts because I don't have any except these,(top one is used), left bottom is for power take off levers, only have 1, the right bottom is without, have 5 of them. I can't remember where I got them it was so long ago.

rollingsculpture · Post by **rollingsculpture** » July 31st, 2013, 8:34 pm

finally able to make it into the shop , 2 platesmade for orders 1 avail since i see Dave/spectria has found his!

aa-fords.com

4-speed floor plate

4-speed floor plate

Re: 4-speed floor plate

Re: 4-speed floor plate

Re: 4-speed floor plate

Re: 4-speed floor plate

Re: 4-speed floor plate

Re: 4-speed floor plate

Re: 4-speed floor plate

Re: 4-speed floor plate

Re: 4-speed floor plate

Re: 4-speed floor plate

Re: 4-speed floor plate