Spindle Bolt and Bearing
Spindle Bolt and Bearing
What is the right and left spindle bolt? I see the tops are off set for the actuator arms.
What way up or down does the spindle bearing go? I see the sides are different, my kit from Snyders only include a felt for the brake rod that goes threw the spindle.
Thanks!
Don Jr.
What way up or down does the spindle bearing go? I see the sides are different, my kit from Snyders only include a felt for the brake rod that goes threw the spindle.
Thanks!
Don Jr.
-
- Posts: 108
- Joined: June 18th, 2014, 10:22 pm
- Body Type: express
- Model Year: 1930
- Location: N. Calif.
Re: Spindle Bolt and Bearing
Hi, here is a picture of the passenger side front brake area. Steve.
- Attachments
-
- kingpin.jpg (288.87 KiB) Viewed 6269 times
-
- Posts: 108
- Joined: June 18th, 2014, 10:22 pm
- Body Type: express
- Model Year: 1930
- Location: N. Calif.
Re: Spindle Bolt and Bearing
Here is a better picture. The "ball" leans forward with respect to center line of the axle. The bearing is below the axle. Slip the pin in but before driving the wedge retaining pin completely home place the brake shaft assembly in place to make sure everything lines up correctly. I have had two instances where the notch in the kingpin where the wedge retaining pin is cut is cut at the wrong angle. Then the brake shaft assembly cannot line up properly and the brake actuating pin gets bound up. I just welded up part of the notch and reground the notch at a better angle to fit. Steve.
- Attachments
-
- kingpin1.jpg (206.54 KiB) Viewed 6267 times
-
- Posts: 108
- Joined: June 18th, 2014, 10:22 pm
- Body Type: express
- Model Year: 1930
- Location: N. Calif.
Re: Spindle Bolt and Bearing
Hi again, I used an air powered cutoff tool to re-cut the notch in the kingpin. Am I the only one that has these funny problems? Steve.
- AAholic
- Posts: 278
- Joined: October 27th, 2010, 7:24 pm
- Body Type: 82-B
- Model Year: 1931
- Location: N.E.Illinois
Re: Spindle Bolt and Bearing
Maybe you got a BB spindle bolt I think the location of the notch is different than on the AA.
-
- Posts: 603
- Joined: May 15th, 2010, 2:34 pm
- Body Type: dump
- Model Year: 1930
- Location: Eastern, CT
Re: Spindle Bolt and Bearing
The spindle bolts for 30-34 are the same.
Red
Red
Re: Spindle Bolt and Bearing
My problem is that I can not get my brake pin to line up with the actuator. It does not hit the little push part. Almost like I have the king pin on the wrong side, but I do have it like the pictures.
I understnad the bearing goes under the axle, but what side is up and what side is down on the BEARING, the two sides of the bearing are different.
Thanks
I understnad the bearing goes under the axle, but what side is up and what side is down on the BEARING, the two sides of the bearing are different.
Thanks
- BrianT
- Posts: 254
- Joined: October 25th, 2013, 8:27 am
- Body Type: 82A
- Model Year: 1929
- Location: San Diego, California
Re: Spindle Bolt and Bearing
Don,
The brake cross shafts are left and right have you tried switching them?, the bearing will have an opening on one side and should face down.
The brake cross shafts are left and right have you tried switching them?, the bearing will have an opening on one side and should face down.
-
- Posts: 1442
- Joined: April 24th, 2003, 11:50 am
- Body Type: Mail truck, Stake tr
- Model Year: 1931
- Location: SO CAL
Re: Spindle Bolt and Bearing
Steve, If you had to recut the slot in the king pins they may have
been for 35-37.
Bob
been for 35-37.
Bob
-
- Posts: 108
- Joined: June 18th, 2014, 10:22 pm
- Body Type: express
- Model Year: 1930
- Location: N. Calif.
Re: Spindle Bolt and Bearing
The one set of spindles that I modified were on a doodle bug and I needed all of the brakes to work, and discovered that the notch was cut at the wrong angle which caused the brake actuating rod to bind. The Kingpin could have indeed been off of a later truck. The other set was a NOS swap meet set that was unmarked so it could have been for a later year as well. Beats a $160 new set. Does anyone know where just the bushings are available for the 30-31 AA truck pins? Thanks, Steve.
-
- Posts: 603
- Joined: May 15th, 2010, 2:34 pm
- Body Type: dump
- Model Year: 1930
- Location: Eastern, CT
Re: Spindle Bolt and Bearing
Steve,
Good luck on the bushings. You can try Bert's and Tam's, I got some from both of them before. No one reproduces them now. I believe Eric Moore has some NOS ones too- E. Moore screen name here on the forum.
Red
Good luck on the bushings. You can try Bert's and Tam's, I got some from both of them before. No one reproduces them now. I believe Eric Moore has some NOS ones too- E. Moore screen name here on the forum.
Red