Early 28 tail pipe hanger

chief5215 · Post by **chief5215** » October 25th, 2015, 2:16 pm

I have a early 28 with the 131 wheel base . I m looking for a picture and or a part number Early 28 tail pipe hanger, And is it reproduced . I have searched the form but I haven't been able to find it Thank You Billy

Bob C · Post by **Bob C** » October 25th, 2015, 2:28 pm

Just go down a few posts to this thread. http://forums.aa-fords.com/viewtopic.php?f=1&t=5312

Bob

chief5215 · Post by **chief5215** » October 25th, 2015, 3:12 pm

I seen that picture and the diagram but it appears in the picture there is a bracket mounted to the frame and then the hanger attached to that. I thought at one time neil had posted a picture of it attached directly to the frame . Thank you

chief5215 · Post by **chief5215** » October 25th, 2015, 3:50 pm

Here is the picture I had on file It is the aa5256b I believe from neil would it be correct for the February 28 or is it the aa5256 without the (B)

: Muffler outlet pipe bracket.jpg (136.3 KiB) Viewed 6439 times

macswoods · Post by **macswoods** » October 25th, 2015, 9:47 pm

Macs has it pt# 28-25239*1 $43.80 get Neal's info and make it your self. my view if not for show I will measure mine if you want.
Mac.......

Brady · Post by **Brady** » October 26th, 2015, 6:43 am

I just use a couple of twisted up coat hangers, then call it a abortion ...

Neil Wilson · Post by **Neil Wilson** » October 26th, 2015, 7:34 am

chief5215 wrote:Here is the picture I had on file It is the aa5256b I believe from neil would it be correct for the February 28 or is it the aa5256 without the (B)

The posted picture is of an AA-5256-B bracket and it was used starting 8/28. From the beginning of production through 8/28 the 5" long AA-5256 bracket was used.

AA-5256 & AA-5256-B.jpg (136.65 KiB) Viewed 6390 times

macswoods · Post by **macswoods** » October 26th, 2015, 2:59 pm

I told you, Neal knows all ! Thanks Neal for all your knowledge about AA trucks. Mac.....

chief5215 · Post by **chief5215** » October 27th, 2015, 2:07 pm

Does anyone have a picture of this bracket mounted, Im trying to figure out the hole locations and which side the castle nut goes on. My is hanging with a piece of pipe strap right now Thanks To all you guys are great.

Neil Wilson · Post by **Neil Wilson** » October 27th, 2015, 2:59 pm

chief5215 wrote:Does anyone have a picture of this bracket mounted, Im trying to figure out the hole locations and which side the castle nut goes on. My is hanging with a piece of pipe strap right now Thanks To all you guys are great.

The attached shows the castle nuts are on the outside of the frame. It would be close to impossible to install the cotters with the nuts on the inside.

macswoods · Post by **macswoods** » October 27th, 2015, 3:04 pm

Neal beat me to it .

chief5215 · Post by **chief5215** » October 27th, 2015, 4:51 pm

Thank you This helps greatly Billy

aa-fords.com

Early 28 tail pipe hanger

Early 28 tail pipe hanger

Re: Early 28 tail pipe hanger

Re: Early 28 tail pipe hanger

Re: Early 28 tail pipe hanger

Re: Early 28 tail pipe hanger

Re: Early 28 tail pipe hanger

Re: Early 28 tail pipe hanger

Re: Early 28 tail pipe hanger

Re: Early 28 tail pipe hanger

Re: Early 28 tail pipe hanger

Re: Early 28 tail pipe hanger

Re: Early 28 tail pipe hanger