hi hope all had a nice thanksgiving. lots to be thankful for in this land of ours.
anyway I have a ? maybe someone can help me with. I have a 1929 82-A the chassis is all done runs and drives thanks to a lot of help
from people on this site. and now its time to put the cab back together but when I got this thing it was all in pieces and I need some step by step
info, on how to assembly it. I have all the new wood top to bottom for it and most of the body work is done I just need to know where to start, final paint will be done after assembly of the cab. thank you for your time.
Dan
cab assembly
-
- Posts: 8
- Joined: July 9th, 2013, 9:14 pm
- Body Type: aa stake
- Model Year: 1930
Re: cab assembly
What state are you in? Best way is probably to drive over and see a assembled cab, talk to the restorer and take some pictures back to develope your assembly plan.
- Neil Wilson
- Posts: 3062
- Joined: February 5th, 2003, 9:42 pm
- Body Type: 82-A/89-A
- Model Year: 1930
- Location: Boulder, CO
- Contact:
82-A Closed Cab
There are some pictures which might help at http://abarnyard.com/temp/82-a/. They were mostly taken to show the restoration of the roof. But they may give you some information on the finished assembly.
The general sequence (as I remember) is:
The lock pillar needs to be installed before the rear corner sheet metal. The rear center and rear corner sheet metal is next. I would install the doors and make sure the door belt moulding aligns with the rear quarter panel belt moulding before installation of any roof wood.
The roof side headers is next followed by the front and rear roof headers. And, finally, the roof bows. The cab must be square before any roof wood is tightened down.
The general sequence (as I remember) is:
The lock pillar needs to be installed before the rear corner sheet metal. The rear center and rear corner sheet metal is next. I would install the doors and make sure the door belt moulding aligns with the rear quarter panel belt moulding before installation of any roof wood.
The roof side headers is next followed by the front and rear roof headers. And, finally, the roof bows. The cab must be square before any roof wood is tightened down.
Regards, Neil Wilson
______________________________________
aafords.com@gmail.com - use this email for contact
https://aafords.com/
______________________________________
aafords.com@gmail.com - use this email for contact
https://aafords.com/
-
- Posts: 8
- Joined: July 9th, 2013, 9:14 pm
- Body Type: aa stake
- Model Year: 1930
Re: cab assembly
thanks Neil for pic, I will go thru theme today and see if I can come with a plan.
Fred I live in Washington state, near Olympia and yes I tried to fine someone around here with a 29 closed cab
that I could look at but know luck . thanks guys ill keep looking and asking
Fred I live in Washington state, near Olympia and yes I tried to fine someone around here with a 29 closed cab
that I could look at but know luck . thanks guys ill keep looking and asking
-
- Posts: 478
- Joined: June 3rd, 2013, 6:15 pm
- Body Type: 186-B stake
- Model Year: 1931
- Location: LHC Arizona & UP Michigan
Re: cab assembly
To justmemachine (name unknown):
Try the Model A Clubs in your area:
Seattle: http://www.evergreenmodela.com/
Tacoma: https://sites.google.com/site/gertieas/
Try the Model A Clubs in your area:
Seattle: http://www.evergreenmodela.com/
Tacoma: https://sites.google.com/site/gertieas/
- elfox
- Posts: 167
- Joined: January 27th, 2011, 8:56 pm
- Body Type: 88-A
- Model Year: 1929
- Location: Port Orchard, WA
Re: cab assembly
Dan -justmemachine wrote:thanks Neil for pic, I will go thru theme today and see if I can come with a plan.
Fred I live in Washington state, near Olympia and yes I tried to fine someone around here with a 29 closed cab
that I could look at but know luck . thanks guys ill keep looking and asking
I live about 1 hour away in Port Orchard. Just let me know if/when you want to take a look at my '29 AA.
- Dave
Dave
Port Orchard, WA
Port Orchard, WA
-
- Posts: 7
- Joined: October 13th, 2014, 1:45 pm
- Body Type: 82-A
- Model Year: 1928
Re: cab assembly
FWIW
Its my understanding there is about a 10 page section in the Les Andrews Vol II that covers the 82-A cab assembly.
On my list of books to get!
Its my understanding there is about a 10 page section in the Les Andrews Vol II that covers the 82-A cab assembly.
On my list of books to get!