Warford 28/29

AA Ford Discussion Group relating to the repair and restoration of your AA Ford.
Post Reply
User avatar
s147881
Posts: 344
Joined: April 13th, 2007, 8:09 pm
Body Type: stake bed 82A
Model Year: 1930
Location: Decatur Michigan

Warford 28/29

Post by s147881 » December 27th, 2017, 1:55 pm

Does anyone know if the warford rear mount is the same as the one for the high/low? Can gear off high low be installed on warford trans rear? I have a chance to purchase one for 600 without rear mount. Just looking if I have a viable solution before spending the money.

Bob C
Posts: 1149
Joined: April 24th, 2003, 11:50 am
Body Type: Mail truck, Stake tr
Model Year: 1931
Location: SO CAL

Re: Warford 28/29

Post by Bob C » December 27th, 2017, 2:13 pm

If you are asking about the part in the left trans in the picture with the two bolts in it, yes.
If you are asking about the bearing retainer on the back of the trans, No

Bob
Attachments
DCP_0397.JPG
DCP_0397.JPG (497.36 KiB) Viewed 714 times

User avatar
s147881
Posts: 344
Joined: April 13th, 2007, 8:09 pm
Body Type: stake bed 82A
Model Year: 1930
Location: Decatur Michigan

Re: Warford 28/29

Post by s147881 » December 27th, 2017, 7:51 pm

I tried to fit a high low rear mount on my last warford and it did not fit. It was close but it looked like the gear piece was at a different angle. It may have just been worn.

User avatar
Neil Wilson
Posts: 2554
Joined: February 5th, 2003, 9:42 pm
Body Type: 89-A
Model Year: 1930
Location: Boulder, CO
Contact:

Re: Warford 28/29

Post by Neil Wilson » December 28th, 2017, 5:18 am

s147881 wrote:
December 27th, 2017, 1:55 pm
Does anyone know if the warford rear mount is the same as the one for the high/low? Can gear off high low be installed on warford trans rear? I have a chance to purchase one for 600 without rear mount. Just looking if I have a viable solution before spending the money.
Part AA-4808 is the "Coupling Shaft Housing Rear Support". This support was used for AA's with the 3-speed transmission (through about Aug. 1929). It was also used for the dual high and Warford transmissions.
Attachments
AA-4808 Coupling Shaft Housing Rear Support 2.jpg
AA-4808 Coupling Shaft Housing Rear Support 2.jpg (223.91 KiB) Viewed 688 times
AA-4808 Coupling Shaft Housing Rear Support 1.jpg
AA-4808 Coupling Shaft Housing Rear Support 1.jpg (403.72 KiB) Viewed 688 times
Regards, Neil Wilson
______________________________________
neil@aafords.com - use this email for contact
www.aafords.com - AA information and photographs

User avatar
s147881
Posts: 344
Joined: April 13th, 2007, 8:09 pm
Body Type: stake bed 82A
Model Year: 1930
Location: Decatur Michigan

Re: Warford 28/29

Post by s147881 » December 28th, 2017, 4:00 pm

Ok thanks

KimVanOrder
Posts: 430
Joined: August 11th, 2013, 4:25 pm
Body Type: 82-A Platform
Model Year: 1928
Location: Hamilton, Mich.

Re: Warford 28/29

Post by KimVanOrder » December 28th, 2017, 6:17 pm

I think I have one of those in the parts box. you need it?
KVO
Dec. '28 AA

User avatar
s147881
Posts: 344
Joined: April 13th, 2007, 8:09 pm
Body Type: stake bed 82A
Model Year: 1930
Location: Decatur Michigan

Re: Warford 28/29

Post by s147881 » December 28th, 2017, 6:38 pm

Thanks but I have a couple.

Post Reply