First AA

AA Ford Discussion Group relating to the repair and restoration of your AA Ford.
Post Reply
User avatar
garagekulture13
Posts: 5
Joined: July 6th, 2018, 8:50 am
Model Year: 1930

First AA

Post by garagekulture13 » August 1st, 2018, 5:19 pm

My name is Coty, I'm 33 and I am from outside of Nashville, Tennessee. I have been lurking on this forum for about a month. I picked up my first AA yesterday out of Georgia. It's a 1930. I say first because I hope it's not my last. I have had a 1930 Model A coupe and currently have a 1931 Model A Tudor. I don't have much information on the truck. So I welcome any info or insight any of you may offer. The truck does not run and I don't have any idea how long it's been sitting. Judging by the running boards running so far back I ASSUME the truck a original express bed truck.ImageImageImageImageImageImage

Sent from my SM-N950U using Tapatalk


Last edited by garagekulture13 on August 1st, 2018, 5:19 pm, edited 1 time in total.

birdacre
Posts: 394
Joined: October 8th, 2013, 2:37 pm
Body Type: AA express
Model Year: 1928

Re: First AA

Post by birdacre » August 1st, 2018, 5:48 pm

your intro sounds like the opening statement at a AA meeting. not to joke about addiciton, but AA's can become a compulsion and expensive habit. nice truck, great photos. thank you.

User avatar
Chris Haynes
Posts: 2005
Joined: September 7th, 2003, 5:18 pm
Body Type: 82A
Model Year: 1930
Location: North Hills, CA/ Pine Grove, CA

Re: First AA

Post by Chris Haynes » August 2nd, 2018, 6:53 pm

Some stake bed models had long running boards and rear fenders. I would start a hunt tracking back owners and see what you find. There may be an Express bed laying by a barn.

Hayslip
Posts: 191
Joined: February 26th, 2007, 6:20 am
Model Year: 1930

Re: First AA

Post by Hayslip » August 3rd, 2018, 6:39 am

Long runningboards were discontinued in July 12,1929 (7-24-29 Indianapolis Service Letter page 2) Your truck was probably an express. You'll need to replace the 1928-mid 30 headlight bar with the curved 1930-1931 style as shown on your car in the photo. Nice truck. Best, Ed
Hayslip

User avatar
Neil Wilson
Posts: 2610
Joined: February 5th, 2003, 9:42 pm
Body Type: 82-A/89-A
Model Year: 1930
Location: Boulder, CO
Contact:

Re: First AA

Post by Neil Wilson » August 3rd, 2018, 6:43 am

garagekulture13 wrote:
August 1st, 2018, 5:19 pm
My name is Coty, ............... Judging by the running boards running so far back I ASSUME the truck a original express bed truck.
Coty, for 1930 only the 89-A express body was used for AA131's with long running boards and long shields.

The gallery at http://aafords.com/aa-chassis/aa-16000-fenders/#rb has a drawing of the AA-16458-B/59-B running boards. The rear fenders used with your truck are AA-16438-C RH & AA-16439-C LH - see http://aafords.com/aa-chassis/aa-16000-fenders/#16438c

See - http://aafords.com/open-bodies/express- ... a-express/ and the detail page at http://aafords.com/open-bodies/express- ... s-details/ for information about the 89-A express body.
Regards, Neil Wilson
______________________________________
neil@aafords.com - use this email for contact
www.aafords.com - AA information and photographs

User avatar
AAholic
Posts: 224
Joined: October 27th, 2010, 7:24 pm
Body Type: 88-A
Model Year: 1931
Location: N.E.Illinois

Re: First AA

Post by AAholic » August 3rd, 2018, 2:21 pm

My truck also had the long running boards and aprons (what was left of them) when I got it and I've wondered if it wasn't an express as well, However couldn't someone have ordered them as an option from the factory or from the dealer back in the day for a stake bed? After all the beds all have fender brackets.
What would the judging standards say? Are period modifications/options points off? What about Coty's 29 headlight bar it may not have left the factory that way but it's still of the period? Regardless it looks like a good solid truck.
John
Attachments
IMG_4922.JPG
IMG_4922.JPG (570.6 KiB) Viewed 1025 times

User avatar
Neil Wilson
Posts: 2610
Joined: February 5th, 2003, 9:42 pm
Body Type: 82-A/89-A
Model Year: 1930
Location: Boulder, CO
Contact:

Re: First AA

Post by Neil Wilson » August 3rd, 2018, 6:42 pm

AAholic wrote:
August 3rd, 2018, 2:21 pm
My truck also had the long running boards and aprons (what was left of them) when I got it and I've wondered if it wasn't an express as well, However couldn't someone have ordered them as an option from the factory or from the dealer back in the day for a stake bed? After all the beds all have fender brackets.
What would the judging standards say? Are period modifications/options points off? What about Coty's 29 headlight bar it may not have left the factory that way but it's still of the period? Regardless it looks like a good solid truck.
John
I suggest you take a look at the introduction of the RGJS. "The Guidelines attempts to define....... as it was driven off the assembly line." If you are interested in having your vehicle agree with the standards, then "period modification" is not what you want. Most don't plan on having their vehicle judged. So, almost anything goes. After sooooo many years parts get changed to whatever fits.

An 88-A platform (like is on your AA) would not have had the fender braces installed from the factory. It is likely the platform on you AA was a replacement sometime in the past. Also, Ford didn't make fenders for dual wheel in 1930.
Regards, Neil Wilson
______________________________________
neil@aafords.com - use this email for contact
www.aafords.com - AA information and photographs

User avatar
garagekulture13
Posts: 5
Joined: July 6th, 2018, 8:50 am
Model Year: 1930

Re: First AA

Post by garagekulture13 » August 4th, 2018, 10:31 am

Thanks everyone. All this information is exactly what I need. There is a round shelf on the interior of the truck on the passenger side in the back cab corner. Is this there for something specific? I will take a pic asap. I also will take a pic of the end of the running board area. As far as where I plan to take the truck I'd like to keep it stock. If possible I'd like to take it back to how this one was made. I don't mean judging condition but I'd like it to be as it was when built.

Sent from my SM-N950U using Tapatalk


RustydoubleA
Posts: 97
Joined: June 18th, 2014, 10:22 pm
Body Type: express
Model Year: 1930
Location: N. Calif.

Re: First AA

Post by RustydoubleA » November 5th, 2018, 8:36 pm

Hi, nice truck! That headlight bar may be original. I bought a late 30 open cab AA farm truck that was kept indoors all of it's life, no rust and mostly stock with the exception of a FABCO frame extension and spring set. It had the 28/29 straight headlight bar with the painted steel 30/31 headlights. I am looking for a picture of it. I actually swapped cabs with a small Model A closed cab pickup, because I wanted a 30/31 Model A roadster pickup and a closed cab AA. I shortened the frame to 131 1/2" so that I could turn around better. I also put in a high speed rear axle as well as cast iron brake drums from a 33 Ford truck, '28 underdrive (retaining the 4 speed) and a B head/cam. And 7.50 x 20 tires like on your truck (you need a lot of LARGE C clamps to squeeze the tire so that the lock ring can be installed). It's fun to bring them back to factory specs, but it's also fun to find the odd parts to enhance the performance. Trucks are what you make them so have fun, learn all that you can and pass it along! Oh, and try not to judge what other people do!

User avatar
garagekulture13
Posts: 5
Joined: July 6th, 2018, 8:50 am
Model Year: 1930

Re: First AA

Post by garagekulture13 » November 23rd, 2018, 3:27 pm

Well here are the pictures I mentioned of the mystery bracket on the passenger side behind the seat and of the ends if the running boards. Just an update the original motor did not have any compression so it was swapped with another used motor I had in the shop. She primarily has only been ran around the neighborhood and used in yard work so far until I feel all the bugs have been worked out. I'm in need of a front bumper and there is one on Ebay now for $200 plus like $80 shipping. Maybe I'm off but it seems a little steep to me. I've asked twice and they won't come down on price.

ImageImageImageImageImage

Sent from my SM-N950U using Tapatalk



Bob C
Posts: 1196
Joined: April 24th, 2003, 11:50 am
Body Type: Mail truck, Stake tr
Model Year: 1931
Location: SO CAL

Re: First AA

Post by Bob C » November 23rd, 2018, 4:10 pm

The bracket is probably for a fire extinguisher. I got a bumper bar for $10 at a swap meet and a bumper and brackets
from a guy for $25.
extinguisher-2.jpg
extinguisher-2.jpg (441.65 KiB) Viewed 209 times
extinguisher.jpg
extinguisher.jpg (165.67 KiB) Viewed 209 times
Attachments
extinguisher-2.jpg
extinguisher-2.jpg (441.65 KiB) Viewed 210 times

ModelAkid
Posts: 468
Joined: June 3rd, 2013, 6:15 pm
Body Type: 186-B stake
Model Year: 1931
Location: SoCal
Contact:

Re: First AA

Post by ModelAkid » November 25th, 2018, 8:37 pm

Hey GK, good news, bad news: I have a front bumper with brackets you can have for $25, bad news is: it is in Upper Michigan, only available in the summer, and I don't want to ship it.

KimVanOrder
Posts: 469
Joined: August 11th, 2013, 4:25 pm
Body Type: 82-A Platform
Model Year: 1928
Location: Hamilton, Mich.

Re: First AA

Post by KimVanOrder » November 26th, 2018, 4:27 pm

ROAD TRIP!!!!!
KVO
Dec. '28 AA

Post Reply