Steering worm removal.
-
- Posts: 753
- Joined: August 11th, 2013, 4:25 pm
- Body Type: 82-A Platform
- Model Year: 1928
- Location: Hamilton, Mich.
Steering worm removal.
I'm looking for ideas on how to get the steering worm gear off the steering shaft. Looks like a splined shaft from what I see. But will not move. Any ideas??
KVO
Dec. '28 AA
Dec. '28 AA
- AAholic
- Posts: 278
- Joined: October 27th, 2010, 7:24 pm
- Body Type: 82-B
- Model Year: 1931
- Location: N.E.Illinois
Re: Steering worm removal.
Heat and or a press, thats how I did mine
-
- Posts: 753
- Joined: August 11th, 2013, 4:25 pm
- Body Type: 82-A Platform
- Model Year: 1928
- Location: Hamilton, Mich.
-
- Posts: 260
- Joined: August 17th, 2019, 1:52 pm
- Body Type: Chassis
- Model Year: 1930
- Location: WV
Re: Steering worm removal.
I am going to need a new worm on mine too. Bottom race is trashed.
-
- Posts: 32
- Joined: October 26th, 2014, 1:00 pm
- Body Type: flat deck
- Model Year: 1928
- Location: Fort St. John, BC, Canada
Re: Steering worm removal.
Don’t forget to remove the C clip first.
-
- Posts: 753
- Joined: August 11th, 2013, 4:25 pm
- Body Type: 82-A Platform
- Model Year: 1928
- Location: Hamilton, Mich.
Re: Steering worm removal.
Is yours all apart? Worm race good? Upper race? Bearings? Hot line to the bank!!
KVO
Dec. '28 AA
Dec. '28 AA
-
- Posts: 260
- Joined: August 17th, 2019, 1:52 pm
- Body Type: Chassis
- Model Year: 1930
- Location: WV
Re: Steering worm removal.
Got the worm off the shaft. Took lots of heat, patience and a heavy puller set up. Press would have been easier. The shaft is taper splined. Looks like I’ll need a sector too. The shaft on my sector is worn egg shaped. Got everything ordered. My old box was dry when I took it apart. Get everything cleaned up now and all threads chased. Not cheap, but should be like new.
-
- Posts: 753
- Joined: August 11th, 2013, 4:25 pm
- Body Type: 82-A Platform
- Model Year: 1928
- Location: Hamilton, Mich.
Re: Steering worm removal.
I'm right behind you!!!!!David R. wrote: ↑September 29th, 2019, 2:57 amGot the worm off the shaft. Took lots of heat, patience and a heavy puller set up. Press would have been easier. The shaft is taper splined. Looks like I’ll need a sector too. The shaft on my sector is worn egg shaped. Got everything ordered. My old box was dry when I took it apart. Get everything cleaned up now and all threads chased. Not cheap, but should be like new.
KVO
Dec. '28 AA
Dec. '28 AA
- Chris Haynes
- Posts: 2203
- Joined: September 7th, 2003, 5:18 pm
- Body Type: 82A
- Model Year: 1930
- Location: Camarillo, CA
Re: Steering worm removal.
I bought a freshly rebuilt F100 unit from Randy Gross. It is a bolt in for a Model A.
-
- Posts: 753
- Joined: August 11th, 2013, 4:25 pm
- Body Type: 82-A Platform
- Model Year: 1928
- Location: Hamilton, Mich.
Re: Steering worm removal.
Dose it 'look'' like an original???Chris Haynes wrote: ↑September 29th, 2019, 9:06 pmI bought a freshly rebuilt F100 unit from Randy Gross. It is a bolt in for a Model A.
KVO
Dec. '28 AA
Dec. '28 AA
- Chris Haynes
- Posts: 2203
- Joined: September 7th, 2003, 5:18 pm
- Body Type: 82A
- Model Year: 1930
- Location: Camarillo, CA
Re: Steering worm removal.
No. But it looks right at home. Plus it works a lot better and doesn't wear out like the A steering always does.KimVanOrder wrote: ↑September 30th, 2019, 4:45 pmDose it 'look'' like an original???Chris Haynes wrote: ↑September 29th, 2019, 9:06 pmI bought a freshly rebuilt F100 unit from Randy Gross. It is a bolt in for a Model A.
https://fordbarn.com/forum/showthread.php?t=144990
https://www.google.com/search?q=Mel+Gro ... lZ2kZSJ0iM:
-
- Posts: 260
- Joined: August 17th, 2019, 1:52 pm
- Body Type: Chassis
- Model Year: 1930
- Location: WV
Re: Steering worm removal.
I bought a freshly rebuilt F100 unit from Randy Gross. It is a bolt in for a Model A.
[/quote]
Dose it 'look'' like an original???
[/quote]
No. But it looks right at home. Plus it works a lot better and doesn't wear out like the A steering always does
How does original column, spark, throttle, horn, light switch work with modern box? I think I’ll stick with the stock unit for now. Grant it a modern design might work better, but the parts are available for the original and it is easily adjusted for wear. As for; “the new box won’t wear out like the A boxes always do”? Give them 90 years. Remember all the original A parts are OLD.
I would think a properly rebuilt and properly maintained original would last as long as a rebuilt modern one.
[/quote]
Dose it 'look'' like an original???
[/quote]
No. But it looks right at home. Plus it works a lot better and doesn't wear out like the A steering always does
How does original column, spark, throttle, horn, light switch work with modern box? I think I’ll stick with the stock unit for now. Grant it a modern design might work better, but the parts are available for the original and it is easily adjusted for wear. As for; “the new box won’t wear out like the A boxes always do”? Give them 90 years. Remember all the original A parts are OLD.
I would think a properly rebuilt and properly maintained original would last as long as a rebuilt modern one.
- Chris Haynes
- Posts: 2203
- Joined: September 7th, 2003, 5:18 pm
- Body Type: 82A
- Model Year: 1930
- Location: Camarillo, CA
Re: Steering worm removal.
Dose it 'look'' like an original???
[/quote]
No. But it looks right at home. Plus it works a lot better and doesn't wear out like the A steering always does
How does original column, spark, throttle, horn, light switch work with modern box? [/quote]
It works perfectly. It is designed to accept the Model" A" parts. This isn't some halfassed thing thrown together. It is well designed with new gears in the box, and a custom made shaft made to accept all of the "A" components.
- AAholic
- Posts: 278
- Joined: October 27th, 2010, 7:24 pm
- Body Type: 82-B
- Model Year: 1931
- Location: N.E.Illinois
Re: Steering worm removal.
I've heard good things about the f150 boxes but If you stick with the original consider a shortened pitman arm, hardly noticeable from the original but makes for more responsive steering, i guess the theory being one needed all the leverage they could get for unpaved rutted roads, it is one of the few concessions I've made with mine.
I also turned a shoulder in the sector housing for a modern seal, to my surprise it's barley leaked a drop since, don't forget the improved STEERING HOUSING END PLATE WITH TUBE A-3568-T 29-31 $9.50 EA but don't waste your money on needle bearings for the sector, I could not tell any difference. With a new worm and sector, bearings,upper and lower races, my rebuild is holding up nicely, with hardly any backlash.
I also turned a shoulder in the sector housing for a modern seal, to my surprise it's barley leaked a drop since, don't forget the improved STEERING HOUSING END PLATE WITH TUBE A-3568-T 29-31 $9.50 EA but don't waste your money on needle bearings for the sector, I could not tell any difference. With a new worm and sector, bearings,upper and lower races, my rebuild is holding up nicely, with hardly any backlash.
- Attachments
-
- A_3568_T.jpg (1.47 KiB) Viewed 8068 times
-
- Posts: 260
- Joined: August 17th, 2019, 1:52 pm
- Body Type: Chassis
- Model Year: 1930
- Location: WV
Re: Steering worm removal.
Chris, that sounds like a good option, but I already have all the parts on the way for my stock unit. I wonder how the modern option compares in price to rebuilding original?
AAholic, I did the same as you and bought the end plate with the long tube and stuck with standard bushings for sector. I didn’t do a modern seal but the o ring and washer. I can live with a little drip here but figured it at least would help shield the grime out from the outside if it doesn’t provide a seal.
My front end was pretty worn out and axle bent, but I found another in better shape. Wow I have a lot of work to do! Haven’t even gotten into engine yet. Working on steering column while I’m waiting on new worm and sector.
AAholic, I did the same as you and bought the end plate with the long tube and stuck with standard bushings for sector. I didn’t do a modern seal but the o ring and washer. I can live with a little drip here but figured it at least would help shield the grime out from the outside if it doesn’t provide a seal.
My front end was pretty worn out and axle bent, but I found another in better shape. Wow I have a lot of work to do! Haven’t even gotten into engine yet. Working on steering column while I’m waiting on new worm and sector.