Page 1 of 2
Steering worm removal.
Posted: September 25th, 2019, 4:34 pm
by KimVanOrder
I'm looking for ideas on how to get the steering worm gear off the steering shaft. Looks like a splined shaft from what I see. But will not move. Any ideas??
Re: Steering worm removal.
Posted: September 25th, 2019, 5:50 pm
by AAholic
Heat and or a press, thats how I did mine
Re: Steering worm removal.
Posted: September 26th, 2019, 11:02 am
by KimVanOrder
AAholic wrote: ↑September 25th, 2019, 5:50 pm
Heat and or a press, thats how I did mine
Thanks... Got it..
Re: Steering worm removal.
Posted: September 26th, 2019, 6:48 pm
by David R.
I am going to need a new worm on mine too. Bottom race is trashed.
Re: Steering worm removal.
Posted: September 27th, 2019, 1:47 pm
by marcel kristoff
Don’t forget to remove the C clip first.
Re: Steering worm removal.
Posted: September 27th, 2019, 4:13 pm
by KimVanOrder
Is yours all apart? Worm race good? Upper race? Bearings? Hot line to the bank!!
Re: Steering worm removal.
Posted: September 29th, 2019, 2:57 am
by David R.
Got the worm off the shaft. Took lots of heat, patience and a heavy puller set up. Press would have been easier. The shaft is taper splined. Looks like I’ll need a sector too. The shaft on my sector is worn egg shaped. Got everything ordered. My old box was dry when I took it apart. Get everything cleaned up now and all threads chased. Not cheap, but should be like new.
Re: Steering worm removal.
Posted: September 29th, 2019, 3:54 pm
by KimVanOrder
David R. wrote: ↑September 29th, 2019, 2:57 am
Got the worm off the shaft. Took lots of heat, patience and a heavy puller set up. Press would have been easier. The shaft is taper splined. Looks like I’ll need a sector too. The shaft on my sector is worn egg shaped. Got everything ordered. My old box was dry when I took it apart. Get everything cleaned up now and all threads chased. Not cheap, but should be like new.
I'm right behind you!!!!!
Re: Steering worm removal.
Posted: September 29th, 2019, 9:06 pm
by Chris Haynes
I bought a freshly rebuilt F100 unit from Randy Gross. It is a bolt in for a Model A.
Re: Steering worm removal.
Posted: September 30th, 2019, 4:45 pm
by KimVanOrder
Chris Haynes wrote: ↑September 29th, 2019, 9:06 pm
I bought a freshly rebuilt F100 unit from Randy Gross. It is a bolt in for a Model A.
Dose it 'look'' like an original???
Re: Steering worm removal.
Posted: September 30th, 2019, 10:44 pm
by Chris Haynes
KimVanOrder wrote: ↑September 30th, 2019, 4:45 pm
Chris Haynes wrote: ↑September 29th, 2019, 9:06 pm
I bought a freshly rebuilt F100 unit from Randy Gross. It is a bolt in for a Model A.
Dose it 'look'' like an original???
No. But it looks right at home. Plus it works a lot better and doesn't wear out like the A steering always does.
https://fordbarn.com/forum/showthread.php?t=144990
https://www.google.com/search?q=Mel+Gro ... lZ2kZSJ0iM:
Re: Steering worm removal.
Posted: October 1st, 2019, 4:11 am
by David R.
I bought a freshly rebuilt F100 unit from Randy Gross. It is a bolt in for a Model A.
[/quote]
Dose it 'look'' like an original???
[/quote]
No. But it looks right at home. Plus it works a lot better and doesn't wear out like the A steering always does
How does original column, spark, throttle, horn, light switch work with modern box? I think I’ll stick with the stock unit for now. Grant it a modern design might work better, but the parts are available for the original and it is easily adjusted for wear. As for; “the new box won’t wear out like the A boxes always do”? Give them 90 years. Remember all the original A parts are OLD.
I would think a properly rebuilt and properly maintained original would last as long as a rebuilt modern one.
Re: Steering worm removal.
Posted: October 1st, 2019, 12:57 pm
by Chris Haynes
David R. wrote: ↑October 1st, 2019, 4:11 am
I bought a freshly rebuilt F100 unit from Randy Gross. It is a bolt in for a Model A.
Dose it 'look'' like an original???
[/quote]
No. But it looks right at home. Plus it works a lot better and doesn't wear out like the A steering always does
How does original column, spark, throttle, horn, light switch work with modern box? [/quote]
It works perfectly. It is designed to accept the Model" A" parts. This isn't some halfassed thing thrown together. It is well designed with new gears in the box, and a custom made shaft made to accept all of the "A" components.
Re: Steering worm removal.
Posted: October 1st, 2019, 7:00 pm
by AAholic
I've heard good things about the f150 boxes but If you stick with the original consider a shortened pitman arm, hardly noticeable from the original but makes for more responsive steering, i guess the theory being one needed all the leverage they could get for unpaved rutted roads, it is one of the few concessions I've made with mine.
I also turned a shoulder in the sector housing for a modern seal, to my surprise it's barley leaked a drop since, don't forget the improved STEERING HOUSING END PLATE WITH TUBE A-3568-T 29-31 $9.50 EA but don't waste your money on needle bearings for the sector, I could not tell any difference. With a new worm and sector, bearings,upper and lower races, my rebuild is holding up nicely, with hardly any backlash.
Re: Steering worm removal.
Posted: October 2nd, 2019, 4:26 am
by David R.
Chris, that sounds like a good option, but I already have all the parts on the way for my stock unit. I wonder how the modern option compares in price to rebuilding original?
AAholic, I did the same as you and bought the end plate with the long tube and stuck with standard bushings for sector. I didn’t do a modern seal but the o ring and washer. I can live with a little drip here but figured it at least would help shield the grime out from the outside if it doesn’t provide a seal.
My front end was pretty worn out and axle bent, but I found another in better shape. Wow I have a lot of work to do! Haven’t even gotten into engine yet. Working on steering column while I’m waiting on new worm and sector.