Universal Joint & drive Shaft Mounting Help
Universal Joint & drive Shaft Mounting Help
Hi,
I have a 1931 AA.
My rear u-joint, which has a 10x10 splines each side, has a fair amount of play in it.
Does anyone have a replacement u-joint or is there a rebuild kit available?
Also, I bought a gasket for the rear u-joint cover from Snyders. It came with a thin metal shim. I am not sure how to know if I need a shim or if it even applies to my AA.
Thanks,
Dave
I have a 1931 AA.
My rear u-joint, which has a 10x10 splines each side, has a fair amount of play in it.
Does anyone have a replacement u-joint or is there a rebuild kit available?
Also, I bought a gasket for the rear u-joint cover from Snyders. It came with a thin metal shim. I am not sure how to know if I need a shim or if it even applies to my AA.
Thanks,
Dave
-
- Posts: 1442
- Joined: April 24th, 2003, 11:50 am
- Body Type: Mail truck, Stake tr
- Model Year: 1931
- Location: SO CAL
Re: Universal Joint & drive Shaft Mounting Help
I don't think you need it on the 1930-31 trucks, it was introduced the end of January 1929.
See page 311 of the Service Bulletins.
See page 311 of the Service Bulletins.
Re: Universal Joint & drive Shaft Mounting Help
Thank you.
Any thoughts on the U-joint? What are people doing to resolve the play in bad joints?
Thanks
Dave
Any thoughts on the U-joint? What are people doing to resolve the play in bad joints?
Thanks
Dave
Re: Universal Joint & drive Shaft Mounting Help
Thank you.
Any thoughts on the U-joint? What are people doing to resolve the play in bad joints?
Thanks
Dave
Any thoughts on the U-joint? What are people doing to resolve the play in bad joints?
Thanks
Dave
-
- Posts: 260
- Joined: August 17th, 2019, 1:52 pm
- Body Type: Chassis
- Model Year: 1930
- Location: WV
Re: Universal Joint & drive Shaft Mounting Help
I am watching. I have one I am sure will need help in this area.
- 1crosscut
- Posts: 877
- Joined: December 25th, 2010, 7:22 pm
- Body Type: 82-A
- Model Year: 1929
- Location: Lincoln, NE
Re: Universal Joint & drive Shaft Mounting Help
I'm not familiar with the specific u-joints of the 31 AA but in the 28/29 u-joints side to side play is fine. It is the rotational play (slop) that is not a good thing.
What type of looseness are you experiencing with yours?
What type of looseness are you experiencing with yours?
------------
Dave
Dave
Re: Universal Joint & drive Shaft Mounting Help
I have rotational play in my u-joint.
-
- Posts: 260
- Joined: August 17th, 2019, 1:52 pm
- Body Type: Chassis
- Model Year: 1930
- Location: WV
Re: Universal Joint & drive Shaft Mounting Help
So it looks like no parts being reproduced for these?
I will have to make my own?
I will have to make my own?
Re: Universal Joint & drive Shaft Mounting Help
How are you going to make repair parts?
My bushings are worn (you can see the gap to the right in the picture) and cracked. I hope that the yoke is OK and the bushings are the expendable parts.
I am surprised that this is not a bigger concern with AA owners. Seems like a part that many people would need to replace.
I wonder if there is a crossover to similar bushings with needle bearings.
Dave
My bushings are worn (you can see the gap to the right in the picture) and cracked. I hope that the yoke is OK and the bushings are the expendable parts.
I am surprised that this is not a bigger concern with AA owners. Seems like a part that many people would need to replace.
I wonder if there is a crossover to similar bushings with needle bearings.
Dave
- Attachments
-
- IMG_0111.JPEG (593.58 KiB) Viewed 5993 times
-
- IMG_0112.JPEG (445.91 KiB) Viewed 5993 times
-
- Posts: 260
- Joined: August 17th, 2019, 1:52 pm
- Body Type: Chassis
- Model Year: 1930
- Location: WV
Re: Universal Joint & drive Shaft Mounting Help
I haven’t crossed that bridge yet, but I am sure I will need to. Especially if the u-joint is as worn out as everything else I’ve encountered on this truck. I am thinking turn new bushings out of 1018 on lathe and case harden?