Fuel Filter Flow Problem
- wv model AA
- Posts: 71
- Joined: April 16th, 2013, 9:24 am
- Body Type: Dump truck
- Model Year: 1931
- Location: Shepherdstown, WV
Fuel Filter Flow Problem
Good Morning Everyone!
I have a 31 AA that has infrequent fuel flow problems in the Fuel Filter. The gas tank has been cleaned. When disconnecting the fuel line that leaves only the Peacock & Fuel Filter only, it flows well. When I have everything connected; the fuel amount in the fuel filter varies when the vehicle is running. The problem is when the truck is idling; it eventually runs out of fuel in the fuel filter and naturally the engine stalls. If the truck is idling and I rev the engine, fuel amount does increase in the fuel filter.
So; what is it that I’m asking? Better consistency fuel amount in the fuel filter to prevent from engine stalling, acting like it’s out of gas. Could it be a “push back” air issue in the fuel filter & line coming from the carburetor? BTW, I’ve tried several different aftermarket fuel filters including the FRAM Fuel Filter recommended from Bratton’s.
SUGGESTIONS?I know I don’t have the correct late period carburetor for my model AA but that’s irrelevant.
Thank you for yuor time,
Jeff
I have a 31 AA that has infrequent fuel flow problems in the Fuel Filter. The gas tank has been cleaned. When disconnecting the fuel line that leaves only the Peacock & Fuel Filter only, it flows well. When I have everything connected; the fuel amount in the fuel filter varies when the vehicle is running. The problem is when the truck is idling; it eventually runs out of fuel in the fuel filter and naturally the engine stalls. If the truck is idling and I rev the engine, fuel amount does increase in the fuel filter.
So; what is it that I’m asking? Better consistency fuel amount in the fuel filter to prevent from engine stalling, acting like it’s out of gas. Could it be a “push back” air issue in the fuel filter & line coming from the carburetor? BTW, I’ve tried several different aftermarket fuel filters including the FRAM Fuel Filter recommended from Bratton’s.
SUGGESTIONS?I know I don’t have the correct late period carburetor for my model AA but that’s irrelevant.
Thank you for yuor time,
Jeff
- Attachments
-
- IMG_0618.JPG (424.89 KiB) Viewed 6323 times
West Virginia Model AA
"Hold My Beer and Watch This..."
"Hold My Beer and Watch This..."
- BrianT
- Posts: 254
- Joined: October 25th, 2013, 8:27 am
- Body Type: 82A
- Model Year: 1929
- Location: San Diego, California
Re: Fuel Filter Flow Problem
Hello Jeff,
Gravity fuel systems are not to tolerant with those inline filters, you may want to turn it around and try it, if your concerned about filtering you can install the pencil filter that fits inside the tank, any fine particles will pass thru the carb jets without a problem, ----in addition I would not use rubber hose under the hood.
Gravity fuel systems are not to tolerant with those inline filters, you may want to turn it around and try it, if your concerned about filtering you can install the pencil filter that fits inside the tank, any fine particles will pass thru the carb jets without a problem, ----in addition I would not use rubber hose under the hood.
-
- Posts: 1442
- Joined: April 24th, 2003, 11:50 am
- Body Type: Mail truck, Stake tr
- Model Year: 1931
- Location: SO CAL
Re: Fuel Filter Flow Problem
You could try something like this from Mike's.
http://www.mikes-afordable.com/product/A9155L.html
Bob
http://www.mikes-afordable.com/product/A9155L.html
Bob
- Attachments
-
- A9155L.jpg (8.35 KiB) Viewed 6302 times
- wv model AA
- Posts: 71
- Joined: April 16th, 2013, 9:24 am
- Body Type: Dump truck
- Model Year: 1931
- Location: Shepherdstown, WV
Re: Fuel Filter Flow Problem
BrianT wrote:Hello Jeff,
Gravity fuel systems are not to tolerant with those inline filters, you may want to turn it around and try it, if your concerned about filtering you can install the pencil filter that fits inside the tank, any fine particles will pass thru the carb jets without a problem, ----in addition I would not use rubber hose under the hood.
I give it a try. Thanks!
/Jeff
West Virginia Model AA
"Hold My Beer and Watch This..."
"Hold My Beer and Watch This..."
- wv model AA
- Posts: 71
- Joined: April 16th, 2013, 9:24 am
- Body Type: Dump truck
- Model Year: 1931
- Location: Shepherdstown, WV
Re: Fuel Filter Flow Problem
Bob C wrote:You could try something like this from Mike's.
http://www.mikes-afordable.com/product/A9155L.html
Bob
Thanks! I'm going to order that. You can tell; I have a the tear drop indent fuel tank. I do have the screen insdie the peacock.
/Jeff
West Virginia Model AA
"Hold My Beer and Watch This..."
"Hold My Beer and Watch This..."
- 1crosscut
- Posts: 877
- Joined: December 25th, 2010, 7:22 pm
- Body Type: 82-A
- Model Year: 1929
- Location: Lincoln, NE
Re: Fuel Filter Flow Problem
I agree. Get rid of that filter. They are not designed for gravity feed fuel systems.
------------
Dave
Dave
-
- Posts: 110
- Joined: June 24th, 2011, 7:35 pm
- Body Type: 188a
- Model Year: 1928
- Location: Tofield, Alberta , canada
Re: Fuel Filter Flow Problem
One other thing to check, make sure your fuel cap vent is working. If it is plugged it will reduce gas flow.
Re: Fuel Filter Flow Problem
maybe your float valve sticks closed once in a while and will not allow fuel to flow? who knows, i would check the needle valve.
Re: Fuel Filter Flow Problem
The original glass bowl filter is best. Even though the tank has been cleaned , ( unless it was removed and cleaned in it's entirety ), there still may be some heavy and small particles in the tank. I ,personally, run the original glass bowl and an inline filter. I use the cylindrical glass type that has a fine mesh screen that is cleanable and reusable. I think made by proline? It filters less microns than a paper one, but allows the fuel to flow effortlessly. The paper ones are for use with pressurized systems. Also, the fuel system requires atmospheric pressure to function properly, meaning that your fuel cap needs to "breath".
-
- Posts: 1223
- Joined: June 14th, 2007, 7:29 pm
- Body Type: Grainbox
- Model Year: 1929
- Location: Illinois
Re: Fuel Filter Flow Problem
or use those cheapo inline fuel filters for riding mowers. same gravity flow fuel system and a carb about as complicated as a model A's they should work great
-
- Posts: 752
- Joined: March 9th, 2009, 8:06 pm
- Body Type: 75-A
- Model Year: 1930
- Location: Sacramento, Ca.
Re: Fuel Filter Flow Problem
Jeff, The L' 31 As did not come with a fuel filter or a screen in the gas tank. The only gas screen I aware of is the one in the carb. I would think that would be the best for you an replace the two peice fuel line with a one peice line! shelby, Sacramento.
- elfox
- Posts: 167
- Joined: January 27th, 2011, 8:56 pm
- Body Type: 88-A
- Model Year: 1929
- Location: Port Orchard, WA
Re: Fuel Filter Flow Problem
I tried to find the fuel filter you show in the picture, but I couldn't narrow it down to a specific one. The micron rating of filters similar to yours varies from 12-70 microns, which is way to fine for a gravity-fed system. Typically, the smaller the number (micron rating) means more restrictive to fuel flow. If you are set on having an inline filter, the absolute smallest micron rating I would go with would be 150 microns, since it wouldn't restrict the fuel flow nearly as much. However, even at 150, it may still be too restrictive. 150 microns is about the size of table salt.
I agree with Mistloop above - I think the glass bowl filter is best. It was designed for this size engine, and can be cleaned and reused.
I agree with Mistloop above - I think the glass bowl filter is best. It was designed for this size engine, and can be cleaned and reused.
Dave
Port Orchard, WA
Port Orchard, WA