Head gasket leak
Head gasket leak
I had my 1930 AA engine rebuilt years ago. The engine builder used a copper head gasket which seeped externally several places around the head after the engine cooled down. A couple weeks ago I replaced the copper gasket with a premium gasket and torqued it per procedure provided with the gasket. The premium gasket stated it didn't require any extra sealant. It seems to have the same problem, maybe even a little worse.
Does anyone have some ideas on what to do next? Is copper with sealant better? Is there something I am missing...
Thanks! Chrism
Does anyone have some ideas on what to do next? Is copper with sealant better? Is there something I am missing...
Thanks! Chrism
-
- Posts: 161
- Joined: July 8th, 2011, 4:36 am
- Body Type: 82-A
- Model Year: 1929
- Location: Townsend,MA
Re: Head gasket leak
Hi, I have been in the same spot and while these leaks are troublesome, unless excessive they are tolerable. If they are not tolerable I have found that head gasket sealer additives cover the small weeping spots that cause these leakes and eliminate the problem. Not a fan of additives but they do work. Just a thought..
-
- Posts: 1223
- Joined: June 14th, 2007, 7:29 pm
- Body Type: Grainbox
- Model Year: 1929
- Location: Illinois
Re: Head gasket leak
did your engine builder deck the head or at least check for flatness? what about the block?Chrism wrote:I had my 1930 AA engine rebuilt years ago. The engine builder used a copper head gasket which seeped externally several places around the head after the engine cooled down. A couple weeks ago I replaced the copper gasket with a premium gasket and torqued it per procedure provided with the gasket. The premium gasket stated it didn't require any extra sealant. It seems to have the same problem, maybe even a little worse.
Does anyone have some ideas on what to do next? Is copper with sealant better? Is there something I am missing...
Thanks! Chrism
I always use copper spray a gasket gasket adhesive on any gasket, havent had any leaks on modern cars nor model A (ive just ran my engine on a test stand)
-
- Posts: 478
- Joined: June 3rd, 2013, 6:15 pm
- Body Type: 186-B stake
- Model Year: 1931
- Location: LHC Arizona & UP Michigan
Re: Head gasket leak
I always use some head gasket sealer when installing a head gasket, and on a flat head like a Model A I put a straight edge on the bottom to make sure it is not warped before I install it. Use the thinnest feeler gauge you have and see if it will go between the head & straight edge anywhere. I hardly ever have head gasket leaks. I prefer the copper/asbestos gaskets like the originals.
Re: Head gasket leak
When replacing head gaskets, especially on a complete rebuild, it is a good idea to check the block for 'flatness' as well as the head! Yes, it is rare, but has been known to happen, & checking it 'now' only takes a few minutes, & is a lot easier than chasing leaks later!
- SteveK535
- Posts: 37
- Joined: October 14th, 2012, 5:26 pm
- Body Type: AA Flatbed Dual Axle
- Model Year: 1931
- Location: Southeast CT
Re: Head gasket leak
You should also recheck torque after several hours of running as it will relax as the gasket sets and the joint completes several thermal cycles. The premium gasket (I'm assuming its the steel silicone composite one from Snyders) is not a copper gasket, and directions say explicitly not to use sealant. I didn't and had some weapage initially, but after I re-torqued it seemed to correct itself.
-
- Posts: 752
- Joined: March 9th, 2009, 8:06 pm
- Body Type: 75-A
- Model Year: 1930
- Location: Sacramento, Ca.
Re: Head gasket leak
I've done a couple of things with great success. One is after checking and cleaning the block and head I use new motor oil all over the new head gasket. Then put the gasket and head on. The advantage of the motor oil on the gasket is to let the gasket spread out to where it needs to go. I have use this method for over 50 yrs. and don't know of any that have fell. That is on small engines, and engines from 1928 thru 1997, including some diesel engines. Try this I think you will be pleased with the results. Also I have sealed Must seeping head gasket with a can of PET evaporated milk. Just add a can to the water in the water in the radiator and drive it until (several time) 'til you do not see any seepage will not hart to just leave it in. What happens is the sugar in the milk will seep in the leak get hot and stop the leak. This is also very go to fix a cracked head or block. Good luck on your repairs Shelby, Sacramento
Re: Head gasket leak
i would just re torque the head gasket. many of the gaskets say that this must be done. who knows the car could be lactose intolerant and then you could have even bigger problems. strange liquids could start coming out any end and horrible burping through the carb. hope this helps.
-
- Posts: 752
- Joined: March 9th, 2009, 8:06 pm
- Body Type: 75-A
- Model Year: 1930
- Location: Sacramento, Ca.
Re: Head gasket leak
I would put the engine oil on a head gasket before I would use any gasket sealer on the market. I never wrote this to educate any one, I'll keep doing this my way. Naturally one would re tark the head nut a couple of times on the engine. I destroyed ONE model A in my over 50 years of working on and with the model A's . I bought a L-31 coupe out of Ca. back in 1982, Solid as a silver dime. Last year I pulled the engine out of my L '31 and sold it to the guy that I was restoring his E '31 coupe. While cleaning and painting I discovered that the engine was a factory rebuilt eng. after running the engine I noticed a water seep on head gasket above oil filler. I attempted to put head. The head must have been put on with JB-WELD. I wound busting the corner off,then from there the rest was in small pieces. Cleaned block, check and installed new head gasket with engine oil on both sides. (No education here!) your vocab. Shelby, Sacramento
Re: Head gasket leak
Decided to pull the head, check flatness and use copper gasket with sealant applied. I cringe at the idea of putting any stop leak product in the radiator.
The copper gasket which came today doesn't have torque instructions. However the rebuild manual I have been working from says 45ftlbs then re-torque to 50 ftlb after a heat/cool cycle. Is that the typical procedure that you know of?
The copper gasket which came today doesn't have torque instructions. However the rebuild manual I have been working from says 45ftlbs then re-torque to 50 ftlb after a heat/cool cycle. Is that the typical procedure that you know of?
-
- Posts: 752
- Joined: March 9th, 2009, 8:06 pm
- Body Type: 75-A
- Model Year: 1930
- Location: Sacramento, Ca.
Re: Head gasket leak
USE MOTOR OIL ONLY
- spectria
- Posts: 1874
- Joined: May 15th, 2008, 9:53 pm
- Body Type: Mail Truck, Stakebed
- Model Year: 1931
- Location: Quincy, Ca.
Re: Head gasket leak
After at least a thousand different engine builds in my shop, as a certified machinist, I have to disagree with Shelby. I have never before heard this recommendation, although it may work in some situations, you should always follow the prescribed techniques for each Gasket application.SHELBY MESSER wrote:USE MOTOR OIL ONLY
I almost always Copper coat spray every gasket that doesn't warn against it.
Some gaskets are not meant to wiggle as would likely happen with a lubricated gasket.
Sry Shelby...
Dave in Quincy, Ca. I love Pics!!!! Post them All!!!
Join the Ford Model AA Truck Club - membership form at http://www.fmaatc.org
Join the Ford Model AA Truck Club - membership form at http://www.fmaatc.org
-
- Posts: 752
- Joined: March 9th, 2009, 8:06 pm
- Body Type: 75-A
- Model Year: 1930
- Location: Sacramento, Ca.
Re: Head gasket leak
You all do it your way I'll do mine my way. NO MORE efforts to to help
- tiredtruckrestorer
- Posts: 338
- Joined: April 20th, 2003, 7:09 pm
- Model Year: 1931
- Location: Orwigsburg, PA
Re: Head gasket leak
An old timer in our Model A Club told me they would put grease on the head gasket before assembly. I never tried it, but that's the way some did it.
Keith
Keith