Don't know which year this AA frame is?

Discussion forum for AA related activities, weekend outings, AA stories etc.
Post Reply
SHELBY MESSER
Posts: 752
Joined: March 9th, 2009, 8:06 pm
Body Type: 75-A
Model Year: 1930
Location: Sacramento, Ca.

Don't know which year this AA frame is?

Post by SHELBY MESSER »

I bought this AA frame-cowl-seat frame from a local guy (second owner in Louisiana) . The truck originally came out of Missouri. I don't know what parts were connected when arriving. When I bought it it was mostly a basket case. The frame had the front and rear axles, engine, tranny, cowl (with a model T windshield) mounted in a wood frame. The cowl is of that of a roadster L'3 -E'31.Front fenders and short running boards mounted. The rest was a basket case. The thing is the frame has no serial. I had the cowl up about 18" Cleaned the frame good and it reviled no serial numbers. I could see where the frame was scratch when being formed. There was no signs of any thing being ground off. I tried acid to see if I could raise any numbers with no luck. Also as wierred as that was there was no serial number on the engine. There are no grind marks,on the pad on the block. I tried acid several times but no numbers appeared. It has a battery cable attached to the starter. The terminal at the starter is stamped 1930. Would this be the year- date of this frame. It is a 131 WB. The engine runs but has a loud wrist-pin knock. The pictures below will explain some
DSCN0256.JPG
DSCN0256.JPG (191.06 KiB) Viewed 72659 times
DSCN0255.JPG
DSCN0255.JPG (160.03 KiB) Viewed 72659 times
Last edited by SHELBY MESSER on January 7th, 2016, 9:38 pm, edited 1 time in total.
User avatar
1crosscut
Posts: 877
Joined: December 25th, 2010, 7:22 pm
Body Type: 82-A
Model Year: 1929
Location: Lincoln, NE

Re: Don't know which year this AA frame is?

Post by 1crosscut »

Bevel gear rear end so sometime mid to late 29 and beyond.
No serial numbers on the engine most likely means it was an industrial engine off a binder, cement mixer etc... not intended to be put in a vehicle.
I have an industrial engine with no serial numbers sitting under my work bench.
------------
Dave
Bob C
Posts: 1442
Joined: April 24th, 2003, 11:50 am
Body Type: Mail truck, Stake tr
Model Year: 1931
Location: SO CAL

Re: Don't know which year this AA frame is?

Post by Bob C »

The frame looks like 30-E31.

Bob
KimVanOrder
Posts: 753
Joined: August 11th, 2013, 4:25 pm
Body Type: 82-A Platform
Model Year: 1928
Location: Hamilton, Mich.

Re: Don't know which year this AA frame is?

Post by KimVanOrder »

Also looks like the rear of the frame has been cut off, Shortened,
KVO
Dec. '28 AA
SHELBY MESSER
Posts: 752
Joined: March 9th, 2009, 8:06 pm
Body Type: 75-A
Model Year: 1930
Location: Sacramento, Ca.

Re: Don't know which year this AA frame is?

Post by SHELBY MESSER »

DSCN0352.JPG
DSCN0352.JPG (176.85 KiB) Viewed 72603 times
DSCN0279.JPG
DSCN0279.JPG (177.37 KiB) Viewed 72595 times
DSCN0351.JPG
DSCN0351.JPG (171.47 KiB) Viewed 72587 times
Last edited by SHELBY MESSER on January 7th, 2016, 9:39 pm, edited 3 times in total.
SHELBY MESSER
Posts: 752
Joined: March 9th, 2009, 8:06 pm
Body Type: 75-A
Model Year: 1930
Location: Sacramento, Ca.

Re: Don't know which year this AA frame is?

Post by SHELBY MESSER »

It being an industrial engine may explain no engine serial # But what would explain no frame serial #. The truck is in very good mechanical shape front fenders are rough. The hood and radiator shell are in great shape. Mechanically The running gear is in good shape Rear springs and hangers are in great shape, The frame has been shorten about 6"or 8" which I have repaired. The clutch and brake peddles has little or no wear on them and the bushings are tight or has no wobble side to side. don't understand why on serial # on frame and engine. Shelby, Sacramento.

Had a better write up an lost it also :evil: :x :D had to sign-in again
SHELBY MESSER
Posts: 752
Joined: March 9th, 2009, 8:06 pm
Body Type: 75-A
Model Year: 1930
Location: Sacramento, Ca.

Re: Don't know which year this AA frame is?

Post by SHELBY MESSER »

DSCN0353.JPG
DSCN0353.JPG (159.99 KiB) Viewed 72586 times
This rear end has lug bolts for duels, but the reams are not for duels.
SHELBY MESSER
Posts: 752
Joined: March 9th, 2009, 8:06 pm
Body Type: 75-A
Model Year: 1930
Location: Sacramento, Ca.

Re: Don't know which year this AA frame is?

Post by SHELBY MESSER »

DSCN0353.JPG
This rear end has lug bolts for duels, but the reams are not for duels.
Bob C
Posts: 1442
Joined: April 24th, 2003, 11:50 am
Body Type: Mail truck, Stake tr
Model Year: 1931
Location: SO CAL

Re: Don't know which year this AA frame is?

Post by Bob C »

What do the rims look like if not for duals?

Bob
SHELBY MESSER
Posts: 752
Joined: March 9th, 2009, 8:06 pm
Body Type: 75-A
Model Year: 1930
Location: Sacramento, Ca.

Re: Don't know which year this AA frame is?

Post by SHELBY MESSER »

The wheels do not have enough off set to be able to put the rims on side by side. I guess that the are the late 1929 wheels. Shelby, Sacramento.
DSCN0273.JPG
DSCN0273.JPG (150.17 KiB) Viewed 72520 times
Attachments
DSCN0275.JPG
DSCN0275.JPG (171.43 KiB) Viewed 72520 times
User avatar
Chris Haynes
Posts: 2203
Joined: September 7th, 2003, 5:18 pm
Body Type: 82A
Model Year: 1930
Location: Camarillo, CA

Re: Don't know which year this AA frame is?

Post by Chris Haynes »

That sure looks to be a Late 1930 0r '31.
Bob C
Posts: 1442
Joined: April 24th, 2003, 11:50 am
Body Type: Mail truck, Stake tr
Model Year: 1931
Location: SO CAL

Re: Don't know which year this AA frame is?

Post by Bob C »

Those wheels are for duals, I think the problem is the tires are to big.
If they are 6.50 or larger they will probably rub. One of the trucks I have
had spacers between the wheels to run 6.50's.

Bob
Attachments
DCP_1001.JPG
DCP_1001.JPG (111.5 KiB) Viewed 72503 times
SHELBY MESSER
Posts: 752
Joined: March 9th, 2009, 8:06 pm
Body Type: 75-A
Model Year: 1930
Location: Sacramento, Ca.

Re: Don't know which year this AA frame is?

Post by SHELBY MESSER »

I do have over size tires on the rear. They are 700 X 20s the guy had two trailers with duals on them, one had 600 X 20s the other had 700s. I told him I wanted the 600s he told me they would be there when you are ready. They had been there for over 15 yrs. all were aired and had good rubber, hardly any wear. I went over about a month later and the trailer with the 600s were gone. I went ahead and took the 700s tires (4) I told him about the trailer was gone. He said he had another trailer at another location that he though had 600s. I didn't go and keep the700s.
Bob the wheel would need 1" spacers in order to fit. Shelby, Sacramento.
Post Reply