Lift Cylinder
- wv model AA
- Posts: 71
- Joined: April 16th, 2013, 9:24 am
- Body Type: Dump truck
- Model Year: 1931
- Location: Shepherdstown, WV
Lift Cylinder
My 31 AA Dump Truck is a Heavy Duty Wood's Bed.
My Lift Cylinder leaks when in used from the stroke rod. A common problem.
The questions is, do you all know a recommended site that may have replacement seals?
I got "sticker shock" over the phone estimate from a professional hydraulic shop to reseal the cylinder.
Thoughts?
My Lift Cylinder leaks when in used from the stroke rod. A common problem.
The questions is, do you all know a recommended site that may have replacement seals?
I got "sticker shock" over the phone estimate from a professional hydraulic shop to reseal the cylinder.
Thoughts?
West Virginia Model AA
"Hold My Beer and Watch This..."
"Hold My Beer and Watch This..."
- wv model AA
- Posts: 71
- Joined: April 16th, 2013, 9:24 am
- Body Type: Dump truck
- Model Year: 1931
- Location: Shepherdstown, WV
Re: Lift Cylinder
Here are some pics.
- Attachments
-
- HYD_2.jpg (17.49 KiB) Viewed 12829 times
-
- HYD_1.jpg (19.21 KiB) Viewed 12829 times
West Virginia Model AA
"Hold My Beer and Watch This..."
"Hold My Beer and Watch This..."
-
- Posts: 1223
- Joined: June 14th, 2007, 7:29 pm
- Body Type: Grainbox
- Model Year: 1929
- Location: Illinois
Re: Lift Cylinder
since you have it out of the truck can you take it to a shop and see what they say? ask around at hyd shops, semi truck repair places, even construction equipment dealers.
OR take the seal out and start taking measurements to see what you find.
OR take the seal out and start taking measurements to see what you find.
- wv model AA
- Posts: 71
- Joined: April 16th, 2013, 9:24 am
- Body Type: Dump truck
- Model Year: 1931
- Location: Shepherdstown, WV
Re: Lift Cylinder
I'm going to take it apart myself.
I called a Hyd. Repair Shop and they estimated $500 and up, up, up to repair it including charging $85 p/hour.
I called a Hyd. Repair Shop and they estimated $500 and up, up, up to repair it including charging $85 p/hour.
West Virginia Model AA
"Hold My Beer and Watch This..."
"Hold My Beer and Watch This..."
-
- Posts: 1444
- Joined: April 24th, 2003, 11:50 am
- Body Type: Mail truck, Stake tr
- Model Year: 1931
- Location: SO CAL
Re: Lift Cylinder
I looked in a Gar Wood catalog and they say four piston rings are used with separate grooves for each ring.
Maybe similar to an engine piston and rings.
Bob
Maybe similar to an engine piston and rings.
Bob
- tiredtruckrestorer
- Posts: 338
- Joined: April 20th, 2003, 7:09 pm
- Model Year: 1931
- Location: Orwigsburg, PA
Re: Lift Cylinder
These older cylinders usually used a rope packing type material. You have to remove the collar where the piston shaft exits the cylinder body. There are two threaded studs with nuts on that hold the collar to the cylinder. Once you remove the collar the packing material should be underneath it. There are usually several layers of packing rings. You'll have to dig these out and try to get measurements. When installing new packing you cut the ends of the material at a 45 degree angle, not a straight 90 degree one. Stager the ends much like you do piston rings. McMaster Carr has packing material. Use the end collar to press the packing material in using the long studs and nuts to press it in. Sometimes you'll have to remove the collar and add more packing. Just don't crack the collar by tightening it up uneven. Sometimes a piece of pipe could be used to help press the packing in before using the collar. The hydraulic pumps and PTO's also used packings quite often back then rather than the seals we think of using today.
Keith
Keith
- wv model AA
- Posts: 71
- Joined: April 16th, 2013, 9:24 am
- Body Type: Dump truck
- Model Year: 1931
- Location: Shepherdstown, WV
Re: Lift Cylinder
Thanks. One more question ! So, the Collar will be able to remove and I shouldn't have to remove the end cover plate?
Most questions I ask are common sense before trying something for the first time on my own. I just want to cover my bases.
The first time I watched this dump bed raise up & down on my AA, I was excited like a little kid.
Most questions I ask are common sense before trying something for the first time on my own. I just want to cover my bases.
The first time I watched this dump bed raise up & down on my AA, I was excited like a little kid.
West Virginia Model AA
"Hold My Beer and Watch This..."
"Hold My Beer and Watch This..."
- gunmetal 2
- Posts: 222
- Joined: April 1st, 2013, 12:51 pm
- Body Type: 82-A
- Model Year: 1929
Re: Lift Cylinder
Take the bolts out of the plate, under that there is probaly a O-ring. take it to a hyd. repair shop and tie to get the O-ring. If you e-mail a pic of the pcs. I can better understand what you have. my e-mail address is 1929oldlady@gmail.com good luke
- wv model AA
- Posts: 71
- Joined: April 16th, 2013, 9:24 am
- Body Type: Dump truck
- Model Year: 1931
- Location: Shepherdstown, WV
Re: Lift Cylinder
Update: I know what the culprit to cause my cylinder to leak. The collar was cracked, welded, and cracked again. Furthermore; the dimensions of the collar that inserts into the cylinder cap has a lot of “slop” by my machinist standards, like .030 because the mounting holes don’t line up which force the cylinder to lift and add pressure against one side of the seal that results in leaking.
So my questions....Does the chamfer or do this design look familiar for a Wood's Collar for a Lift Cylinder ???
So my questions....Does the chamfer or do this design look familiar for a Wood's Collar for a Lift Cylinder ???
- Attachments
-
- collar2.jpg (19.25 KiB) Viewed 12707 times
-
- collar1.jpg (15.18 KiB) Viewed 12707 times
West Virginia Model AA
"Hold My Beer and Watch This..."
"Hold My Beer and Watch This..."
Re: Lift Cylinder
It's probably a waste of time to repair that collar: it's been brazed & re-broken, so it's probably quite brittle by now. If you have access to a milling machine(or know someone who does) I recommend making a new piece out of mild steel (instead of what looks like cast iron) for several reasons :1. it won't be brittle(bend instead of breaking) 2.much easier to make(the old piece, if repaired properly, needs to be machined anyway) 3. cost the same or less than the repairing the existing piece & wind up with a better part.
- wv model AA
- Posts: 71
- Joined: April 16th, 2013, 9:24 am
- Body Type: Dump truck
- Model Year: 1931
- Location: Shepherdstown, WV
Re: Lift Cylinder
Oh, I will definitely make a new part from mild steel with tighter tolerances.
West Virginia Model AA
"Hold My Beer and Watch This..."
"Hold My Beer and Watch This..."
- tiredtruckrestorer
- Posts: 338
- Joined: April 20th, 2003, 7:09 pm
- Model Year: 1931
- Location: Orwigsburg, PA
Re: Lift Cylinder
Yes, the chamfered collar looks typical of an older hydraulic cylinder. That should press against the packing material inside squeezing it against the cylinder shaft. Was there any packing material left inside?
Keith
Keith
- wv model AA
- Posts: 71
- Joined: April 16th, 2013, 9:24 am
- Body Type: Dump truck
- Model Year: 1931
- Location: Shepherdstown, WV
Re: Lift Cylinder
The only thing I see what appears to be a "rubber" seal. It looks fine and I don't believe its correct for the time period.
One a happier note. I laid a 12 scale against the shaft. Its perfect shape & straight.
I'm highly convince the old collar is the problem.
One a happier note. I laid a 12 scale against the shaft. Its perfect shape & straight.
I'm highly convince the old collar is the problem.
West Virginia Model AA
"Hold My Beer and Watch This..."
"Hold My Beer and Watch This..."