Maple floorboards
-
- Posts: 478
- Joined: June 3rd, 2013, 6:15 pm
- Body Type: 186-B stake
- Model Year: 1931
- Location: LHC Arizona & UP Michigan
Maple floorboards
Is anyone making & selling the original style maple planks that made up the original floorboards from 1928 to around mid-'29? They were made in the factory for wood products that Ford built in Kingsford Michigan, where Ford owned thousands of acres of woodlands nearby, where maple trees are very common. All the wood for all Ford "woody" station wagons came from there also, which is probably why the wood for those was all maple & birch.
More trivia:
The Kingsford Ford factory operated from 1921 to 1951.
During WW2 they built glider planes out of wood.
To make use of waste sawdust & scraps, Henry started the Kingsford Charcoal Co.
The official mascot name of Kingsford High School is the "Flivvers".
To have enough electrical power for the factory, Ford built a hydro-electric power dam on the nearby Menominee River. That was sold to the Wisconsin-Michigan Power Co. in 1953.
~ from the (rare) book "Kingsford, the Town that Ford Built" (1998).
More trivia:
The Kingsford Ford factory operated from 1921 to 1951.
During WW2 they built glider planes out of wood.
To make use of waste sawdust & scraps, Henry started the Kingsford Charcoal Co.
The official mascot name of Kingsford High School is the "Flivvers".
To have enough electrical power for the factory, Ford built a hydro-electric power dam on the nearby Menominee River. That was sold to the Wisconsin-Michigan Power Co. in 1953.
~ from the (rare) book "Kingsford, the Town that Ford Built" (1998).
- Neil Wilson
- Posts: 3062
- Joined: February 5th, 2003, 9:42 pm
- Body Type: 82-A/89-A
- Model Year: 1930
- Location: Boulder, CO
- Contact:
Re: Maple floorboards
Floorboards for what????? Cab, cargo body (which body) ???????????
Regards, Neil Wilson
______________________________________
aafords.com@gmail.com - use this email for contact
https://aafords.com/
______________________________________
aafords.com@gmail.com - use this email for contact
https://aafords.com/
-
- Posts: 1444
- Joined: April 24th, 2003, 11:50 am
- Body Type: Mail truck, Stake tr
- Model Year: 1931
- Location: SO CAL
Re: Maple floorboards
There are cab maple floor boards on Ebay but they don't look very good, no dovetail and the boards only look about two or three
inches wide. https://www.ebay.com/itm/Ford-Model-A-F ... BO&vxp=mtr
Bob
inches wide. https://www.ebay.com/itm/Ford-Model-A-F ... BO&vxp=mtr
Bob
-
- Posts: 478
- Joined: June 3rd, 2013, 6:15 pm
- Body Type: 186-B stake
- Model Year: 1931
- Location: LHC Arizona & UP Michigan
Re: Maple floorboards
Thanks Bob. Those ebay floorboards are fairly decent but they only have flat, glued together edges, not like the interlocking edge routing of the originals which used no glue. Originals also had pegs inserted to hold the boards together as well as the steel supports riveted to the underside. I have a bunch of the original boards but not enough good pieces to assemble a floorboard set. The boards are only 2-3" wide. I think all '28-9 Model A & AA cars & trucks had the same size front floorboards, but the cutouts can vary.
- 1crosscut
- Posts: 877
- Joined: December 25th, 2010, 7:22 pm
- Body Type: 82-A
- Model Year: 1929
- Location: Lincoln, NE
Re: Maple floorboards
I made a set for my truck a few years ago. They can be a bit of a challenge to make.
------------
Dave
Dave
- 1crosscut
- Posts: 877
- Joined: December 25th, 2010, 7:22 pm
- Body Type: 82-A
- Model Year: 1929
- Location: Lincoln, NE
Re: Maple floorboards
Hmmmm... I may have to post pictures separately. Tried several at one time and only one came through.
- Attachments
-
- 001.jpg (593.26 KiB) Viewed 7388 times
------------
Dave
Dave
-
- Posts: 478
- Joined: June 3rd, 2013, 6:15 pm
- Body Type: 186-B stake
- Model Year: 1931
- Location: LHC Arizona & UP Michigan
Re: Maple floorboards
Nice job, crosscut! I like your dovetail interlocking joints like original, and the pegs inserted. Where did you get the cutters for the interlocking joints?
Re: Maple floorboards
i can't seem to visualize the rubber door straps. they look like they go from the door jam to the front cowl panel??? not hooked to door???
- 1crosscut
- Posts: 877
- Joined: December 25th, 2010, 7:22 pm
- Body Type: 82-A
- Model Year: 1929
- Location: Lincoln, NE
Re: Maple floorboards
ModelAkid - Only one cutter bit is needed to make them. Just a single pass for the female. For the male it takes one pass on each side to cut it. Is a bit of a bugger to get the male centered, the right thickness and depth to make a joint that fits snug but can still slide. Considerable trial and error.
Birdacre - the door straps are not yet attached to the doors in the picture making them look odd.
Birdacre - the door straps are not yet attached to the doors in the picture making them look odd.
------------
Dave
Dave
Re: Maple floorboards
thanks for info. i will send a photo of my dec 28 AA floor boards. i believe they are original and maple. they have neat angles around the pedals and fit together in a really neat way. i will send photo to illustrate. very nice work.
-
- Posts: 478
- Joined: June 3rd, 2013, 6:15 pm
- Body Type: 186-B stake
- Model Year: 1931
- Location: LHC Arizona & UP Michigan
Re: Maple floorboards
Crosscut, can you tell me the brand & part number of the bit used to cut the interlocking edges? Also what power tool did you mount that on?