Starting Crank Bearing

AA Ford Discussion Group relating to the repair and restoration of your AA Ford.
Post Reply
Dan 82-A
Posts: 5
Joined: July 19th, 2012, 11:26 am
Body Type: 82-A PU
Model Year: 1929

Starting Crank Bearing

Post by Dan 82-A »

Is the Starting Crank Bearing for a 29 AA the same as a 29 A? This would be part number A-5461-B.

I see there is an AA-5461 listed for 30-31 in the Parts Price List, Effective July 1, 1931, but I don't see a listing for a 28-29 Starting Crank Bearing.

The reason for the question is that there is a Starting Crank Bearing in place on a 29AA which looks a larger/taller A version. This is one with the U bolts. The problem is that the hand crank won't fit into the crankshaft nut, the bearing makes it too high. The motor mounts are all stock and in good shape.
User avatar
Neil Wilson
Posts: 3062
Joined: February 5th, 2003, 9:42 pm
Body Type: 82-A/89-A
Model Year: 1930
Location: Boulder, CO
Contact:

Re: Starting Crank Bearing

Post by Neil Wilson »

Dan 82-A wrote:
October 12th, 2021, 12:29 pm
Is the Starting Crank Bearing for a 29 AA the same as a 29 A? This would be part number A-5461-B.

I see there is an AA-5461 listed for 30-31 in the Parts Price List, Effective July 1, 1931, but I don't see a listing for a 28-29 Starting Crank Bearing.

The reason for the question is that there is a Starting Crank Bearing in place on a 29AA which looks a larger/taller A version. This is one with the U bolts. The problem is that the hand crank won't fit into the crankshaft nut, the bearing makes it too high. The motor mounts are all stock and in good shape.
The 1929 AA used A-chassis, A-5461 starting crank bearing. This bearing has flat flanges for the square-design spring clips. Starting June 1929 an oil hole was added to this bearing (this was the design 3 bearing). A bearing which requires u-shaped clips is incorrect.
Attachments
A-5461-d3-q8.jpg
Regards, Neil Wilson
______________________________________
aafords.com@gmail.com - use this email for contact
https://aafords.com/
Dan 82-A
Posts: 5
Joined: July 19th, 2012, 11:26 am
Body Type: 82-A PU
Model Year: 1929

Re: Starting Crank Bearing

Post by Dan 82-A »

The A Starting Crank Bearing will be easy to find.
I'll have to start looking for a couple of AA-5455 spring clips to fit what ever spring is under there, I may have one.
Thanks Neil!
User avatar
Neil Wilson
Posts: 3062
Joined: February 5th, 2003, 9:42 pm
Body Type: 82-A/89-A
Model Year: 1930
Location: Boulder, CO
Contact:

Re: Starting Crank Bearing

Post by Neil Wilson »

Dan 82-A wrote:
October 12th, 2021, 1:38 pm
The A Starting Crank Bearing will be easy to find.
I'll have to start looking for a couple of AA-5455 spring clips to fit what ever spring is under there, I may have one.
Thanks Neil!
More than likely, your 1929 AA has the front cross member with a slightly wider channel (1/29 Ford Service Bulletin). Consequently, it requires the AA-5455-B clips to be used with the AA-5458 design 2 clip bar (see attached). I don't yet have a drawing the the AA-5455-B clip (but, it will be slightly wider than the AA-5455 clip). This drawing will be orders in the near future.
Attachments
AA-5458-d2-cb-q8.jpg
Regards, Neil Wilson
______________________________________
aafords.com@gmail.com - use this email for contact
https://aafords.com/
Dan 82-A
Posts: 5
Joined: July 19th, 2012, 11:26 am
Body Type: 82-A PU
Model Year: 1929

Re: Starting Crank Bearing

Post by Dan 82-A »

Ok, I will check out the measurement of the clip bar when I get it off.
The crossmember does have a reinforcement riveted on the underside area that meets the spring.
User avatar
Neil Wilson
Posts: 3062
Joined: February 5th, 2003, 9:42 pm
Body Type: 82-A/89-A
Model Year: 1930
Location: Boulder, CO
Contact:

Re: Starting Crank Bearing

Post by Neil Wilson »

Dan 82-A wrote:
October 12th, 2021, 11:04 pm
Ok, I will check out the measurement of the clip bar when I get it off.
The crossmember does have a reinforcement riveted on the underside area that meets the spring.
Your #1 cross member is most likely a replacement. Ford upgraded the service cross members to include the reinforcement (like the 30/31 cross member).
Regards, Neil Wilson
______________________________________
aafords.com@gmail.com - use this email for contact
https://aafords.com/
Dan 82-A
Posts: 5
Joined: July 19th, 2012, 11:26 am
Body Type: 82-A PU
Model Year: 1929

Re: Starting Crank Bearing

Post by Dan 82-A »

Thanks Neil.
Yes, I took a closer look and the crossmember is bolted in.
Post Reply