Got my first AA so new to this world. 29 stake bed single rear wheels.
Rear drum stuck hard even pulling with tractor left rear slides.
1. Are lug bolts swedged to drum like the A?
2. Are there any vendors selling new drums?
New to the AA so please excuse my ignorance
Don in Georgia
donsan5502@att.net is my email
Rear brake drums-removal
- Neil Wilson
- Posts: 3071
- Joined: February 5th, 2003, 9:42 pm
- Body Type: 82-A/89-A
- Model Year: 1930
- Location: Boulder, CO
- Contact:
Re: Rear brake drums-removal
A 29 AA would have a worm drive rear axle. Wheel bolts are swedged to the drum /hub. New hubs and or drums are not being made for AA trucks.
Regards, Neil Wilson
______________________________________
aafords.com@gmail.com - use this email for contact
https://aafords.com/
______________________________________
aafords.com@gmail.com - use this email for contact
https://aafords.com/
- Chris Haynes
- Posts: 2208
- Joined: September 7th, 2003, 5:18 pm
- Body Type: 82A
- Model Year: 1930
- Location: Camarillo, CA
Re: Rear brake drums-removal
Is yours the worm drive or the split case Timken rear end?
-
- Posts: 607
- Joined: May 15th, 2010, 2:34 pm
- Body Type: dump
- Model Year: 1930
- Location: Eastern, CT
Re: Rear brake drums-removal
I thought the hub studs had nuts on the insides holding the studs on? I know the '31 front drums have nuts holding the studs on.
Red
Red
- 1crosscut
- Posts: 884
- Joined: December 25th, 2010, 7:22 pm
- Body Type: 82-A
- Model Year: 1929
- Location: Lincoln, NE
Re: Rear brake drums-removal
Hi Don.
If you haven't already back off the brake adjuster all the way. If that doesn't help you might consider removing the brake rods just to make sure they are not hanging up causing the problem.
If after that it still is not coming loose then try using a torch to heat the drum up to make it expand. Move the torch around and around and around... you get the idea of the circumference of the drum to expand it. A few whacks with a hand sledge during the process will help.
If you haven't already back off the brake adjuster all the way. If that doesn't help you might consider removing the brake rods just to make sure they are not hanging up causing the problem.
If after that it still is not coming loose then try using a torch to heat the drum up to make it expand. Move the torch around and around and around... you get the idea of the circumference of the drum to expand it. A few whacks with a hand sledge during the process will help.
------------
Dave
Dave
Re: Rear brake drums-removal
Thanks everyone. As soon as the weather breaks I will light up the torch and get to work.
-
- Posts: 1455
- Joined: April 24th, 2003, 11:50 am
- Body Type: Mail truck, Stake tr
- Model Year: 1931
- Location: SO CAL
Re: Rear brake drums-removal
Can you rotate the drum? Is the hub broke loose from the axle?
-
- Posts: 266
- Joined: August 17th, 2019, 1:52 pm
- Body Type: Chassis
- Model Year: 1930
- Location: WV
Re: Rear brake drums-removal
Bevel gear or worm drive? I disassembled three bevel gear axles. A couple came off hard. You need a VERY stout puller and big hammer, lots of penetrating oil and perhaps a little heat from torch. On one I had to free up frozen brake adjusters with penetrating oil and torch to be able to back brakes off. Photo of puller set up I used. I made an adapter from a junk wheel center.